HomeMy WebLinkAbout31700 GRAPE ST_ 2077 (55)31700 GRAPE STREET 2077 24/30
WAL -MART
j THIS FILM WAS PHOb1DCED FROM
TIM BEST AND MOST COMPLETE
1 PUT111'f(8 AVAILABLE AT THE
OF FIWM `.. .t
f-•
r.
i
3. Conductors size #10 AWG and smaller may be stranded or solid and shall have insulation type
THWN or THIAN.Conductors sized #8 AWG and larger shall be stranded and shall have
insulation type THW, THWN, THHN, or XHHW.
4. No wire shall be smaller than #12 AWG unless otherwise noted, except wiring for signal and
pilot control circuits may be #14 MTW or TFF, unless otherwise noted.
5. Color code conductors in accordance with the 1990 NEC 210 -5, 2006 and the following:
SYSTEM NEUTRAL PHASE CONDUCTOR EQUIP. GROUND
VOLTAGE COLOR COLOR COLOR
1
208/120V white A- black, B -red, C -blue green
480/277V h. gray A- brown, B- orange, C- yellow green
6. #10 AWG and smaller phase conductors shall be color coded by a continuous outer covering.
Conductors larger than #10 AWG may be culor coded by tape or paint.
7. Identify circuit numbers with synthetic cloth labels.
K. Wiring devices:
1. Switches: Branch circuit switches shall be specification grade rated 20A 120/277 VAC as follows:
a. Single pole: CS120BI by Bryant or acceptable substitute.
b. Three way: CS320BI by Bryant or acceptable substitute.
2. Receptacles: : Oupta d
20e
1 5of
the
611 y giant` type specification grade as follows:
b . Duplex receptacle 20A 125V 53621 by Bryant.
a Duplex receptacle 20A 125V Isolated ground 53621G by Bryant.
3. Cover Plates: Provide cover plates for devices of size, type and design to suit the outlet box
a. Where devices are Installed on exposed fittings or boxes, plates are galvanized steel.
2.02 IDENTIFICATION OF EQUIPMENT
A. Laminated plastic: nameplates with 3/4 Inch mirdrtwm contrasting color engraved letters for each
panelboard, switch, contactor panel, or individually mounted contactor.
The nameplates are permanently attached to equipment and shall clearly Identity the equipment ortheequipmentserved, such as PANEL LD ", etc.
PART 3 EXECUTION
3.01 EXAMINATION
A. Examine surfaces anti adjacent areas in which Work under this Section Is to be performed. Report in
writing to the Wal -Mart Construction Manager prevailing conditions that may adversely affectsatisfactoryexecutionofWork. Do rat proceed with Work until unsatisfactory conditions have been
corrected.
1
B. Starting Work constitutes acceptance of the existing conditions and this Contractor shall then, at his
1 expense, be responsible for correcting all unsatisfactory and defective Work encountered.
3.02 PREPARATION
A. EDC equipment under this Sedan is intended to be utilized for temporary power and for permanent
power. Coordinate requirements with Section 01500 and the following:
1. Local utility company for providing she electrical transformer and metering.
2. She grading in the preparation of running primary power from off -she to on -she electrical
1 transformer.
a Grades to be within 2 inches of final grades before installation of primary power.
3. Construction of EDC footingstpad, transformer pad and related building installation
requirements.
a. Before completion of foundation stem wall and the delivery of structural steel, coordinate
installation of EDC structure.
B. Ensure that concrete encased grounding electrodes have been provided Prd coordinated with EDC
installation.
July 16,1993
1
B. Items of switchgear, including switchboards, panelboards, safety switches, etc. will be the product of
SECTION 16400 one of the followng manufacturers, unless otherwise noted on Drawings.
b WM: -EDC 12022 1. Eaton (Cutler Hammer).
SERVICE AND DISTRIBUTION 2. General Electric.
3. Seimens (ITE).
4. Square D.
PART 1 GENERAL 5. Westinghouse.
1.01 SUMMARY C. Structure: Enclosure structure shall be compete, ready for installation and service:
1. Fully assembled electrical center built of structural steel base, walls, and removeable roof with
A. Section Includes: cross members for support .
1. Owner- Furnished, pre - manufactured Electrical Distribution Center (EDC), including but not limited 2. Structural steel hase: Built to properly support the weights of the components during shipping
to the following: and providing a proper base for the system when Installed in accordance with the Drawings and
a. Service entrance switchgear and associates items of equipment. Specifications.
b. Panelboards, and related distribution equipment.
Lighting Including interface for Energy
3. Wall components: Bulk to properly support factory mounted components in addition to field
mounted components as indicated on the Drawings and in these Specifications. a contactors arJ controls components
Management control of lighting, power drops and signage. 4. Floors: Fire retardant pressure treated 3/4" plywood, painted.
5. Electrical Distribution Center: Equipped NEC. Doorsd. Transformers.
e. Grounding.
j with the appropriate number of exits per
screened for ventilation and equipped with hardware for locks
6. Pre lights, and on the Drawings. f. Telephone backboards.
g. Alarm system backboards.
wired service receptacles, switches as shown
7. Safety and warning signs as required by the National Electrical Code and local codes and
h. Energy Management System backboards and associated interconnections. j requirements.
8. Accessories:
B. Products Installed, but not Furnished under this Section: a. Self contained battery operated emergency lighting system.
1. Owner's Electrical Distribution Center (EDC) supplier will furnish EDC components as indicated b . Fire extinguisher appropriately rated for use In electrical equipment rooms.
on Drawings under provisions of Section 01010:
2. Owner's Electrical Distribution Center (EDC) supplier will provide setting Drawings, templates, D. Service Entrance and Switchgear:
and directions for installation of EDC. 1. Swhchgear with service entrance section and indoor metering compartments where required by
C. Related Sections:
the local Utility and Indicated on Drawings.
Outdoor disconnects to be by Owner, shipped loose for field Installation. a provkJed
1. Section 01010 -Summary of Work: General procedures related to Owner furnished products. i b. "Outdoor" metering equipment to be provided by Contractor.
2. Section 01310 -Progress Schedule: Mile, .one construction schedule. 2. Service equipment shall be as Indicated and scheduled on the Drawings. Service entrance
3. Sedan 0'500 - Construction Facilities and Temporary Controls: Coordinate installation of equipment, UL listed as suitable for use as s.., /ice equipment.
foundations and floor slab preparations for ualy installation of EDC unit(sp. EDC unit is 3. Switchboare.: Configured as scheduled on the Drawings, Including voltage, amperage, bus
designed for early use in the project and is Intended for use as temporary power.
4. Section 03300 - Cast -Place Concrete: Early of concrete base(s) for setting o`.
j bracing, arvJ interrupting ratings.
a. Main rugs only (MLO), main circuit breaker (MCB), or main fusible switch (MFS) and branchInpreparation
EDC prior to laying of CMU walls. devices as indicated on the schedule.
5. Section 13810 - Energy Management System: 4. Service entrance switchboards and panelboards with main circuit breakers, main fusible switches
or branch devices rated 1000 amperes or above are equipped with ground fault protection.
1.02 REFERENCES 5. Main fusible switches or fusible switch type branch devices are equipped with rejection type
fuse holders and fuses as indicated on the Drawings.
A. Work under this Sectk.n whail oomply with the following:
1. Latest edition of the National Electric Safety Code, the National Electric Code, and interim E. Distribution and Lighting/Appliance Panelboards:
amendments in effect. 1. Panelboards: Configured as scheduled on the Drawings, Including voltage, amperage, bus
2. Conily with local and state, utility regulations and laws. bracing, and interrupting rol;ngs.
a. Provide main lugs only (MILD), main circuit breaker (MCB), or main fusible switch (MFS)
B. Electrical Distribution Centers shall be listed by ETL Laboratories or Underwriters Laboratories as a and branch devices as indicated on the schedule.
compete assembly and shall bear the appropriate label showing that listing. b . Branch Circuit Prot&.tIve Devices: Plug -on or bolted tyyppe thermal magnetic center -trip
circuit breakers for zltemating current, each with single hart9e common trip. Tandem or
1.03 SYSTEM DESCRIPTION half-sized circuit breakers or bad center type constru, an will rat be permitted. Circuit
breaker Amp Inter-dpting Capacity (AIC) shall be reu than the values Indicated on the
A. Electrical Distribution Center (EDC): Pre - manufactured electrical dlstribution renter and pre-
ass
Drawings. Circult breakers feeding emergency lights, night liIgghts, time clock motors, etc.
manufactured satellite console units as Indicated nn Drawings. shall be equipped with handle -locks where indicated on the Drawings.
C.. Cabinets: Zinc- coated sheet steel with knock -outs, UL listed and labeled. Trims and doors
B. EDC unh(s` Is fabricated, complete with tho following, ready for setting: shall have a suitable primer coat and a Iinish coat of the manufacturer's standard color.
lock latch. Locks be1. DetaAable lift connections. Trims shall be fined with hinged doors having combined and shall
2. Mezzanine structure with supports for field assembly, keyed alike ark fumished with two keys for each panelboard.
d. Directory Holder: A legible typewritten circuit directory properly Identifying load(s) on each
C. Electrical System Voltages: The following voltages shall apply unless otherwise noted. circuit mounted under a clear plastic cover. Connect circuits exactry as indicated on Panel
1. Main Service: 277/480 votes, 3 phase, 4 wire wye, 60 hertz, grounded neutral. Schedule: no deviation will be tolerated.
2. Receptacle and small power systems: 120/208 volts, 3 phase, 4 wire wye, grounded neutral.
3. Sales area and stockroom lighting systems: 277 volts, 3 phase, 4 wire wye, grounded neutral. F. Transformers: Pre- inst¢Jled as shown on the Drawings.
4. Parking lot lighting: 480 volts unless ct anged by Owner. 1. Transformera for 4,eneral use at 600 volts and below are two winding, dry-type. Transformers
C 40`C5. The Energy Management System: 24 VAC. are rated for full -load operation at a maximum of 150 temperature rise above a ambient,
iunless otherwise Indicated on the Drawings.
1 I 16400-3
16400-1 1 WM - Lake Elsinore, CA July 16,1993
WM - Lake Esinore, CA July 16, 1993
j
j THIS FILM WAS PHOb1DCED FROM
TIM BEST AND MOST COMPLETE
1 PUT111'f(8 AVAILABLE AT THE
OF FIWM `.. .t
f-•
r.
i
3. Conductors size #10 AWG and smaller may be stranded or solid and shall have insulation type
THWN or THIAN.Conductors sized #8 AWG and larger shall be stranded and shall have
insulation type THW, THWN, THHN, or XHHW.
4. No wire shall be smaller than #12 AWG unless otherwise noted, except wiring for signal and
pilot control circuits may be #14 MTW or TFF, unless otherwise noted.
5. Color code conductors in accordance with the 1990 NEC 210 -5, 2006 and the following:
SYSTEM NEUTRAL PHASE CONDUCTOR EQUIP. GROUND
VOLTAGE COLOR COLOR COLOR
1
208/120V white A- black, B -red, C -blue green
480/277V h. gray A- brown, B- orange, C- yellow green
6. #10 AWG and smaller phase conductors shall be color coded by a continuous outer covering.
Conductors larger than #10 AWG may be culor coded by tape or paint.
7. Identify circuit numbers with synthetic cloth labels.
K. Wiring devices:
1. Switches: Branch circuit switches shall be specification grade rated 20A 120/277 VAC as follows:
a. Single pole: CS120BI by Bryant or acceptable substitute.
b. Three way: CS320BI by Bryant or acceptable substitute.
2. Receptacles: : Oupta d
20e
1 5of
the
611 y giant` type specification grade as follows:
b . Duplex receptacle 20A 125V 53621 by Bryant.
a Duplex receptacle 20A 125V Isolated ground 53621G by Bryant.
3. Cover Plates: Provide cover plates for devices of size, type and design to suit the outlet box
a. Where devices are Installed on exposed fittings or boxes, plates are galvanized steel.
2.02 IDENTIFICATION OF EQUIPMENT
A. Laminated plastic: nameplates with 3/4 Inch mirdrtwm contrasting color engraved letters for each
panelboard, switch, contactor panel, or individually mounted contactor.
The nameplates are permanently attached to equipment and shall clearly Identity the equipment ortheequipmentserved, such as PANEL LD ", etc.
PART 3 EXECUTION
3.01 EXAMINATION
A. Examine surfaces anti adjacent areas in which Work under this Section Is to be performed. Report in
writing to the Wal -Mart Construction Manager prevailing conditions that may adversely affectsatisfactoryexecutionofWork. Do rat proceed with Work until unsatisfactory conditions have been
corrected.
1
B. Starting Work constitutes acceptance of the existing conditions and this Contractor shall then, at his
1 expense, be responsible for correcting all unsatisfactory and defective Work encountered.
3.02 PREPARATION
A. EDC equipment under this Sedan is intended to be utilized for temporary power and for permanent
power. Coordinate requirements with Section 01500 and the following:
1. Local utility company for providing she electrical transformer and metering.
2. She grading in the preparation of running primary power from off -she to on -she electrical
1 transformer.
a Grades to be within 2 inches of final grades before installation of primary power.
3. Construction of EDC footingstpad, transformer pad and related building installation
requirements.
a. Before completion of foundation stem wall and the delivery of structural steel, coordinate
installation of EDC structure.
B. Ensure that concrete encased grounding electrodes have been provided Prd coordinated with EDC
installation.
July 16,1993
WM:
SECTION 16011
ELECTRICAL SYSTEMS TESTING
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Electrical systems testing and forms.
PART 2 PRODUCTS Not Used.
05202
f
PART EXECUTION
3.01 TESTING
I' ^on completion of installation, perform continuity tests on power and equipment branch circuit
I ..iductors. Inspect wire and cable for physical damage. Verity proper phasing connections. Torque
test conductor connections terminations to manufacturer's recommended values.
B . Inspect panelboards for physical damage, Proper alignment, anchorage, and grounding. Check
Iproper installation and tightness of connections for circuit breakers, fusible switches, and fuses.
C. Measure ground resistance from system neutral connection at service entrance to convenient ground
point on building water pipe using suitable ground testing equipment. Resistance shall not exceed
10 ohms.
D. Teat integrity of isolated grounding system for cash register panels by measuring resistance from
system neutral to Isolated ground bar and from conduit system to Isolated ground bar before and
1 after isolated grounding conductor, neutral conductor, grounding conductor, and transformer case are
bonded together.
E. Test receptacles with circuit tester to ensure proper polarity, grounding,and continuity of circuits.
f F. With parking lot lighting on, measure voltage at branch breaker and at farthest light fixture for each
t lighting circuit. Refer to Section 16530, Part 3, Sizing.
G. Record measurements and results on following Electrical Systems Testing Form. This form must be
forwarded to Wal -Mart before final payment will be made.
END OF SECTION
WM - Lake Elsinore, CA
16011 -1
July 16,1993
ELECTRICAL SYSTEM TESTING FORM
TestForm 09299
For complete Instructions, refer to the Electrical System Testing Section of Specifications. Show values in
appropriate box.
PARKING--
LOT LIGHT
CIRCUIT
NUMBER
ON " 5a • • • ACTUA
SIZE I O
12102
BASIC ELECTRICAL MATERIALS AND METHODS
PART GENERAL
1.01 SUMMARY
A. Related Sections:
1. Motors and motor controls will be furnished and installed under other Sections unless otherwise
noted on Drawings.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B. Product Data:
1. Wire Connector: If any other type of material is proposed for use on any size conductor, submit
for review prior to use.
2. Wire and Cable: Submit material construction data, insulation thickness, jacket thickness, and test
data for review upon request.
C. Samples: Submit wire and cable upon request.
PART PRODUCTS
2.01 IDENTIFICATION OF EQUIPMENT
A. Fumish laminated plastic nameplates with 3/4 Inch minimum corttrastigkoolor engraved letters for each
panelboard, safety switch, contactor, time switch, and pushbuHon. The nameplates shall be bolted
Identity
This Form signifies that the above measurements have been made, that all receptacles have been tested for
proper grounding, polarity, and continuity- that the integrity of the cash register isolated grounding system has
been tested, and that all components of the electrical system have been tested to ensure their proper
operation.
TESTED BY Date ,
Electrical Contractor)
VERIFIED BY Date
General Contractor)
I
1
I
i
16011 -2
WM - Lake Elsinore, CA July 16, 1993
TUIS N 11AG PIlt0O1 M FR011
THE BEST AND SORT COMM
DMINCIS AVAILABLE AT THE
VA TW OF FILMM-41— dF
f SECTION 16050
t' WM: 12102
BASIC ELECTRICAL MATERIALS AND METHODS
PART GENERAL
1.01 SUMMARY
A. Related Sections:
1. Motors and motor controls will be furnished and installed under other Sections unless otherwise
noted on Drawings.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B. Product Data:
1. Wire Connector: If any other type of material is proposed for use on any size conductor, submit
for review prior to use.
2. Wire and Cable: Submit material construction data, insulation thickness, jacket thickness, and test
data for review upon request.
C. Samples: Submit wire and cable upon request.
PART PRODUCTS
2.01 IDENTIFICATION OF EQUIPMENT
A. Fumish laminated plastic nameplates with 3/4 Inch minimum corttrastigkoolor engraved letters for each
panelboard, safety switch, contactor, time switch, and pushbuHon. The nameplates shall be bolted
Identityorpop- riveted to equipment and shall clearly the equipment or equipment served, such as
PANEL LD" , "BALER ", etc.
2.02 CONDUIT RACEWAYS
A. Size all conduits in accordance with the NEC, but in no case less than the following:
1. Security, Data, and Telephone Systems: 3/4 Inch minimum, unless otherwise noted.
2. Flexible Conduit Not Exceeding 72 Inches, for Connection of Light Fixtures Recessed In
Suspended Ceilings: 3/8 inc4 minimum.
3. Underground Conduits in Parking Lot: 3/4 Inch minimum.
4. Telephone: 1/2 Inch minimum.
S. Other Uses: 1/2 Inch minimum.
B. Conduit Types Permitted (Must bear the UL label):
i 1. Galvanized Rigid Metal Conduit (GRC): Hot -dip galvanized, manufactured by Republic or
approved equal.
2. Aluminum Rigid Metal Conduit: Manufactured by Kaiser Aluminum, Harvey Aluminum, or
approved equal.
3. Intermediate Metal Condult (IMC): Hot -dip galvanized, manufactured by Republic or approved
equal.
4. Electrical Metallic Tubing (EMT): Hot -dip galvanized, manufactured by Republic or approved
equal.
5. PVC Rigid Nonmetallic Conduit (PVC). Schedule 4o heavy -wall PVC manufactured by Carton, or
approved equal.
6. Flexible Metal Conduit: Zinc- coated steel, manufactured by Republic or approved equal.
7. Liquidtlght Flexible Metal Conduit: Seal -Tile, with PVC jacket.
I 2.03 WIRES AND CABLES
A. Wire and cable as indicated and required by the Drawings shall bear the UL label and stamping
indicating wire size, type, voltage, and grade, and shall meet the standard specifications and tests
established for such materials and construction by ASTM, NEMA, ANSI, and IPCEA where
applicable.
July 16, 1993
s7
B.
I
Wire shall be code gage, soft annealed copper, not less than 98% conductivity and of the 600 volt i 6. Outdoor EMT fittings shall be of the compression type.
2.12
class, unless otherwise noted. I
I, A. Provide as indicated on Drawings or as required.
I
P PART
C. Conductors size #10 AWG and smaller may be stranded or solid and shall have insulation type
THWN THHN. Conductors #8 AWG larger be have insulation
INSTALLATION
2.06 WIRING DEVICES
or size and shall stranded and shall
type THW, THWN, THHN, or XHHW. "B.X." cable is not acceptable.
A. Switches:
1. Branch circuit switches shall be specification grade rated 20A 120/277V AC as follows:
switches, circuit breakers, and other similar devices and equipment will vary depending upon locationI
a. Single Pole: CS120BI, by Bryant.
D. No wire shall be smaller than #12 AWG, unless otherwise noted, except that wiring for signal and b. Single Pole Weatherproof Cover: 63071, by Bryant.
pilot control circuits may be #14 AWG, unless otherwise noted.
D. Existing Electrical Lines: If any existing power, telephone, or other electrical lines and appurtenances
a Double Pole: 45221, by Bryant.
are encountered which interfere with the proper installation of new work and which will not be used in
connection with new work, close such items in proper manner and, It necessary, move or remove the
d. Three Way: CS320BI, by Bryant.
E. Color code conductors in accordance with the 1987 NEC 210.5 and the following:
than required and repair affected surfaces to match adjacent surfaces.
2. Where switches operating at 277 volts are ganged, furnish permanently installed barriers
Equipment Pads: Furnish and install concrete transformer pads, it required, and concrete foundations
NEUTRAL PHASE CONDUCTOR EQUIP. GROUND
for parking lot lighting standards as Indicated on the Drawings.
between switches in accordance with the 1984 NEC 380 -8(b).
Access to Equipment: Locate all control devices, specialties, pull boxes, etc., so as to provide for
SYSTEM VOLTAGE COLOR COLORS COLOR 1
easy access of operation, repair, and maintenance and, if concealed, furnish and install access doors.
I B. Receptacles:
J
208/120V A- black, B C
I. Trenching: Perform all trenching and backfilling in accordance with the Site Utilities Section of these
1. Outlet devices shall be grounding -type specification grade as follows:
Specifications.
white -red, -blue green
4801277V It. grey A- yellow, B- orange, C -brown green
CONDUIT
a. Single Receptacle 20A/250V: 54611, by Bryant.
b. Single Receptacle /20A 125V: 53611, by Bryant.
Installation:
1. Install wiring in oonduh, unless otherwise rated in the Drawings or Specifications.
a Single Receptacle 20A/125V Isolated Ground: 5361IG, by Bryant.
F. 10 AWG and smaller phase and neutral conductors shall be color coded by a continuous outer
covering. Conductors larger than #10 AWG maybe color coded by tape or
3. Securely support conduit and piping by means of approved hangers. Support spacing shall
be in accordance with the NEC. Make necessary provisions for expansion of conduit and
d. Duplex Receptacle 20A/1 25V: 53621, by Bryant.
Duplex Receptacle
securely anchor conduh where necessary to property distribute stresses.
paint.
4. Flexible metal conduit: Support every 4' -6" and within 12 inches of terminations, with Caddy
e. 20A 125V Isolated Ground: 5362 IG, by Bryant.
I. Duplex ;leceptacfe 20A/1 25V Weatherproof: 5362/868, by Bryant.
G . Identify circuit numbers with synthetic cloth labels.
5. Liquidt ht flexible metal conduit: Support every 4' -6" and within 12 inches of terminations, per
g. Clock Receptacle 15AM 25V: 2828G, by Bryant.
6. Keep openings in conduits closed during the progress of the work. Swab conduits clean before
pulling wire.
h. GFI Receptacle 15A/125V Weatherproof: GFR52FTI /GFRWPV, by Bryant. 2.04 WIRE CONNECTIONS AND DEVICES
9. Openings around electrical penetrations through fire - resistance rated walls, partition;, floors, or
ceilings shall be firestopped using approved to fire
I. Cash Register Receptacle 15A1125V Isolated Ground: 47101G, by Bryant.
Yellow Connector: Dual
A. Run conductors without splices from outlet to outlet, except within junction boxes. Make splices in 11
with earth with two heavy continuous coats of asphaltic paint or other approved conduit
ff -Lite 1CDB1 -N; no substitutions.
k Orange Connector Isolated
No.8 AWG and smaller wire whh insulated Ideal Wingnut, 3M Scotchlok, or approved equal J Ground: Dual -Life MS1•N; no substitutions.
Device face made of material other than nylon or lexan.
connectors of proper size. 3M No. 567 in -line self- stripping connectors may be used for ballast lead
connections in fluorescent light rows only. Make splices in 716 AWG and larger wire with approved
Call (405) 848 -7548 or (918) 838.8718 lt clarifications are needed.
solderless lugs and connectors. If any other type of connector is proposed for use on any size C. Cover Plates: Provide cover plates for devices, of size, type and design to suit outlet box.
conductor, submit for approval prior to use. 1. Where devices are installed on exposed fittings or boxes: Plates to be galvanized steel.
2. Weatherproof cover plates: Gasketed cast or stamped metal with gasketed device cover.
B . Modular wiring connection systems may be used for wiring between individual sales floor lighting Plastic weatherproof plates are rat acceptable.
fixtures only. Modular wiring system shall be supported in a workmanlike manner and all "homeruns' 3. Temperature Sensor J- Boxes: Nylon switch cover plates.
shall be sized as indicated on the plans.
D. Colors:
2.05 OUTLET BOXES AND CONDUIT FITTINGS 1. Unless otherwise noted, wiring devices and cover plates for flush mounting shall be ivory nylon.
2. Blank Cover Plates: On boxes without devices or fixtures, provide same type and color as
A. Interior boxes shall be hot -dip galvanized, 4 Inches minimum octagon or square, unless otherwise installed on devices in that same room or area.
noted. Boxes for outlets installed flush in drywall construction may be single or multiple gangs as 3. Isolated ground receptacles: Orange nylon cover plates.
required. 9oxes for outlets installed flush in concrete block or brick walls shall be masonry boxes
manufactured by Raco, Steel City, Appleton, or approved equal. Single surface - mounted outlet
boxes be handy boxes.
E. Acceptable Manufacturers:
shall 1. Wiring devices and plates as manufactured by Arrow Hart,P &S /Sierra, Bryant, Hubbell, Leviton,
General Electric, and Eagle, are acceptable, with the exception that designated receptacles, as
B . Boxes shall comply with NEC In regard to maximum allowable number of conductors.
l
previously specified, have no substitutions permitted.
2. Devices or plates found to be not as specified shall be removed and replaced with specified
C. Outlet boxes Intended to support lighting fixtures shall be suitable for the purpose. 1 device or plate at Contractor's expense.
D. Floor Junction Boxes: O.ZJGEDNEY Cat. No. YR060604, or approved substitute. 2.07 PANELBOARDS
E. Conduit Fittings: A. Manufacturer:. quare D Powerlink, Square D Company - Control Products Division. (918)622 -2800.
1. Steel: Appleton TW and TWC series; O.ZJGEDNEY 6000S and 7000S series; ETP 2200 series Contact: Mr. Russ Diehl.
or approved equal. Diecast with Steel Nut: Appleton 95T and 96T series or approved equal. 1. Substitutions: None accepted.
Diecast: Appleton 93T and 94T series or approved equal.
2. Indoor EMT fittinggs may be of the diecast or all steel set screw type.
3. Outdoor GRC, IMC, EMT box be Meyers Seal hubs,
B. Branch Circuit Protective Devices: Plug -on or bolted type thermal magnetic center -trip circuit breakers
or connections shall made with -rite for alternating current, each with single - handle common trip. Tandem or half-sized circuit breakers or
O.Z. /GEDNEY (IT Series)) Space Maker hub, Appleton Uni -Seal hub or approved equal.
4. Threadless GRC or IMC fittings shall not be used. Indoor GRC or IMC connections shall be
load center type construction will not be permitted. Circuit breaker Amp Interrupting Capacity (AIC)
shall be no less than the indicated the Drawings. Circuit breakers feeding
made with double locknuts and bushings.
5. PVC fittings the type be for PVC
values on emergency
lights, night lights, time clock motors, etc. shall be equipped with handle -locks where Indicated on the
of solvent weld shall used conduit. Drawings.
1. Circuit breakers serving lighting, signage and selected power circuits as indicated on the
drawings, shall be Square D Powerlink, Type 00-PL (120/208V) or EHB -PL (277/480V), number1ofpolesantiamperageratingasindicatedonthedrawingschedules.
C. Cabinets: Zinc - coated sheet steel with knockouts, UL listed and labeled. Trims and doors shall have
a suitable primer coat and a finish coat of the manufacturer's standard color. Trims shall be fitted with
16060 2 160503
WM - Lake Elsinore, CA July 16,1993 WM - Lake Elsinore, CA July 16, 1993
f,
r.:.:, ,.+r.,w...Vs;.,v...s4swrtw'Swv wi,..a i>..iYA .c^aw:!iaiK- 1»x.+r!hKan> Tk'*b ff!R.M' .,•f'P.' ",:t Vic, n3,. hti t - =. ,.u.w.e.. _.:..:.... i. .... ,_,.
THIS FILM WAS PRODOCRD FM
THR BRST AND MOST CO11PU&TR
i DRAWINGS AVAILARLR AT TBR ,';:
rips OF ri
E
2.11 CONCRETE PADS
I
A. Concrete strength and reinforcing as indicated on Drawings.
2.12 ACCESS DOORS
I, A. Provide as indicated on Drawings or as required.
I
P PART EXECUTION
5.01 INSTALLATION
A. Install specified materials in accordance with manufacturer's recommendations and as indicated on
Drawings.
B . Heights of Disconnect Switches, Protective Devices, Etc.: The mounting height of disconnect
switches, circuit breakers, and other similar devices and equipment will vary depending upon locationIandwhetherindividuallyorgroupmounted.
C. Unless otherwise noted on the Drawings, mount equipment as follows:
1. Individual Device: Operating handle, lever, or button 5' -0" approximately.
2. Panelboards: Highest overcurrent protective device 6-0" maximum.
D. Existing Electrical Lines: If any existing power, telephone, or other electrical lines and appurtenances
are encountered which interfere with the proper installation of new work and which will not be used in
connection with new work, close such items in proper manner and, It necessary, move or remove the
tines as directed by Owner.
E. Cutting and Patching: Where cutting is required through walls, floors, or ceilings, make openings no
larger than required and repair affected surfaces to match adjacent surfaces.
F. Equipment Pads: Furnish and install concrete transformer pads, it required, and concrete foundations
for parking lot lighting standards as Indicated on the Drawings.
G . Access to Equipment: Locate all control devices, specialties, pull boxes, etc., so as to provide for
easy access of operation, repair, and maintenance and, if concealed, furnish and install access doors.
H. Painting: Touch -up items of equipment whose factory finish has been marred or damaged during
Installation, restoring it to its original Allappearance. other painting will be done by the General
Contractor.
I. Trenching: Perform all trenching and backfilling in accordance with the Site Utilities Section of these
Specifications.
3.02 CONDUIT
IA. Installation:
1. Install wiring in oonduh, unless otherwise rated in the Drawings or Specifications.
2. Install conduits concealed, except in unfinished areas and where indicated on the Drawings.
3. Securely support conduit and piping by means of approved hangers. Support spacing shall
be in accordance with the NEC. Make necessary provisions for expansion of conduit and
securely anchor conduh where necessary to property distribute stresses.
4. Flexible metal conduit: Support every 4' -6" and within 12 inches of terminations, with Caddy
I Clips or equal, in accordance with the 1987 NEC 350.4.
1 5. Liquidt ht flexible metal conduit: Support every 4' -6" and within 12 inches of terminations, per
1984 NEC 351-8.
6. Keep openings in conduits closed during the progress of the work. Swab conduits clean before
pulling wire.
7. Clean PVC conduit per manufacturer's recommendations before application of solvent cement.
8. Furnish and install flashings where conduits penetrate the roof membrane.
t
9. Openings around electrical penetrations through fire - resistance rated walls, partition;, floors, or
ceilings shall be firestopped using approved to firemethodsmaintainthe - resistance rating.
10. Paint metallic conduits concealed under concrete poured on grade or where installed in contact
i16050
with earth with two heavy continuous coats of asphaltic paint or other approved conduit
5
WM - Lake Elsinore, CA July 16, 1993
4 :.
t. ,,X,H;c. ,,.. .::.. Fad
f
a
D. EDC unit is manufactured complete as follows: j
1. Switchgear including metering section when required by lo-;' authority having jurisdiction. I2. Panelboards, including feeder conductors from switchgear.
3. Dry type, step -down transformers including primary and secondary conductors.
4. Grounding conductors from each transformer to a centrally located chase through the floor of the
EDC, with sufficient length of conductor for connection to grounding electrode.
5. Lighting control panels Including control wiring to the Energy Management System, Section
13810.
6. Clearly defined field termination points.
7. Panels, switches and transformers with labels and completed index of circuits.
8. Wiring diagrams for lighting control circuits.
9. Plywood mounting boards, stenciled and pre -wired for telephone, alarm, energy management,
and intercom equipment. '
10. Service outlets, general and emergency Illumination.
1.04 SUBMITTALS
A. Submit the following in accordance with Section 01300.
B. Shop Drawings:
1. Owner's EDC supplier will prepare shop drawings and forwaru to Architect's Electrical
Consultant under rovisions of Section 01300.
2. Shop drawings will indicate: Profiles, sizes, spacing, and k ations of components, connections,
attachments, and fasteners.
3. Product Data will indicate: Switchgear, panelboards, trs-isformers, lighting contactors, lighting
contactor panels, circuit breakers, and fuses.
1.05 DELIVERY, STORAGE, AND HANDLING
A. Provide for delivery of equipment and materials at such stages of work as will expedite work and
minimize project storage requirements.
B . Coordinate delivery of hems furnished under this Specfioation.
C. Obtain manufacturer's Information drawings, rigging diagrams, and equipment specifications to assure ,
that the Electrical Distribution Centers will be received, instal;ad and connected in such a manner as to
provide a complete, workmanlike installation of the system with no damage to the components or
adjacent work.
D. Electrical Distribution Centers are manufachired and delivered as weatherproof units. Maintain units in
weatherproof condition until building is enck fed and weatherproof packaging may be removed.
1.(6 SEQUENCING AND SCHEDULING
A The responsibility of Work under this Section includes, but is not limited to, the following:
1. Contact EDC manufacturer to coordinate and schedule delivery to she.
2. Wurk under this Section is inter0ed for use as temporary power. Ensure that provisions for
l operation is provided in conjunction with construction schedule.
3. Insure that preparation for the installation of this Work is provided. Preparation shall include, but
Is not limited to, the following:
a. She grading be!ore installation of primary power and she transformer.
b. Installation and preparation of structural support for EDC Unit.
a Groundiry requirements for EDC Unh.
d. Receipt and placement of EDC Unit within building structure.
4. Place EDC unit in full operation as defined within this Section.
PART 2 PRODUCTS
2.01 PRE- MANUF4CTURED ELECTRICAL DISTRIBUTION CENTER
A. Owner - Furnished EDC, 5y Electrical Distribution Systems, Inc., Conyers, GA. Contact Ken Stevens
at (404)388 -0706.
16400-2
WM - Lake Els:nnre, CA July 16, 1993
1
i
2. Transformers have 2 to 2 -1/2 %, above and below, voltage taps on the primary windings and
shall conform to NEMA standard. '
G. Fuses:
1. 601 ampere and above, all voltages: Bussmann KRP -C Hi -Cap.
2. 600 ampere and below, 480 volt: Bussmann LPS - RK.
3. 600 ampere and below, 250 volt: Bussman LPN - RK.
4. Approved Fuse Manufacturers:
a. Bussmann.
b. Gould Shawmut.
C. Little Fuse.
H. Control Panels:
1. Control Devices: Installed and pre -wired on the line side, pre -wired to terminal strips ready for '
field connection to the bad. A complete and simplistic wiring diagram for field connection of
switched branch circuits is provided.
2. Control wiring and Energy Management System Interface wiring for switched loads is pre - wired.
3. Termination for parking lot lighting circuits with a wire range of #10 AWG to #4 AWG is provided. '
4. Control devices are manufactured by one of the following:
a. Asco Contactorz.
b. Eaton (Ctdler Hammer) conlactors.
a Seimens (ITE) contactors.
Id. Square D contactors.
e. Westinghouse contactors.
I. Novar controls !lghting control unh with GE RR7 relays.
I. Conduit and Fittings: '
1. Size all conduits in accordance with the National Electrical Code, but in no case less than the
following:
a. Security, Data. and Telephone systems: 3/4 inch minimum unless otherwise noted. '
b. Telephone individual outlets whhm the Electrical Distribution Center: 1/2 Inch minimum.
a Other uses: 112 inch minimum.
2. Conduit types permitted (Bearing UL or ETL label):
a. Galvanized Rigid Metal Conduit (GRC): Hot -dip galvanized, manufactured by Republic or
approved equal.
b. Aluminum Rigid Metal Conduit: Manufactured by Kaiser Aluminum, Harvey Aluminum or
approved equal.
a Intermediate Metal Conduit (IMC): Hot -dip galvanized, manufactured by Republic or '
approved equal.
d. Electrical Metallic Tubing ( °.MT): Hot -dip galvanized, manufactured by Republic or
approved
e. Flexible Meal Conduit: Zinc- coated steel, manufactured by Republic, or aluminum by
Reynolds, or acceptable substitute.
3. Interior outlet boxes shall be hot -dip galvanized, 4 inches minimum octagon or square, unless
otherwise rated. Single surface boxes shall be handy boxes. Boxes shall be manufactured
by Raco, Steel City, Appleton, or approved equal.
4. Pull and junction boxes shall be made of code gauge steel, fabricated in accordance with the
requirements of the NEC and underwriters Laboratories requirements.
5. Boxes shall co ,iply with NEC and Underwriters Laboratories requirements in regard to
maximum allowa7le number of conductors. '
6. Outlet taxes Intended to support lighting Iixtums shall be suitable for that purpose.
7. Conduit fittings:
a. St,)el: Appleton TW and TWC series: O.Z. GEDNEY 6000S and 7000S series; ET 2200
sedes or approved equal. Diecast with steel nut; Appleton 95T and 96T series or
ap roved equal. Diecast: Appleton 93T and 94T series or approved equal.
b. I oor EMT fitting may be of the diecast or all steel set screw type.
a Theadless GRC or IMC fittings shall not be used. Indoor GRC or IMC connections shall
be made with double locknuts and bushings.
J. Conductors*
1 Wire and cable as indicated by the Drawings shall bear the UL label and stamping indicating
wire, size, type, voltage, and grade, and shat! -*feet the standard specifications and tests
established for such materials and construction by ASTM, NEMA, ANSI, and IPCEA where
applicable.
2. Wire shall be made of code gauge, soft annealed copper, ..of less than 98% conductivity and of
the 600 voh class, unless otherwise noted.
16400 -4
WM - Lake Elsinore, CA July 16, if 93
C. Structure: Set EDC on prepared base, plumb and level, in strict accordance with manufacturer's
instructions at location(s) indicated on Drawings. Secure in place in accordance with manufacturer's
instruction, including mezzanine structure(s) if indicated.
3.03 FIELD WORK RELATING TO EDC UNIT INSTALLATION
A. Check terminations and re- torque per manufacturer's instructions.
B . Service entrance conductors.
C. Branch circuit connections.
D. Grounding conductor terminations to electrodes.
E. Field termination of lighting and controlled bad branch circuits.
F. Field installed feeders as indicated on Drawings.
3.04 SERVICE ENTRANCE
A. Contractor shall contact local electric utility upon award of contract to arrange for early installation of
permanent power to site. Coordinate tim(ng of this Installation with the arrival date and installation of
EDC.
B . If early installation of permanent power cannot be accomplished, provide and Install adequate
temporary service(s), until permanent power can be installed.
3.05 ELECTRICAL SERVICE
A. Coordinate electrical service and metering requirements with the serving utility prior to installation.
Provide required material and labor, in accordance with the utility company's requirements, necessary
to provide a complate electric service as indicated on the Drawings.
B. Required hems include, but are not limited to, trenching and backfilling, primary and secondary
conduits, service conductors (including primary conductors where required), C.T. cabinet and other
associated metering hardware, and the grounding system.
C. Perform Work in strict compliance with the local utility's requirements and with any applicable local
codes.
D. Contractor shall pay all utility company charges associated with providing service to this project
Including, but not limited to, charges for service, demand meter pulse generator, and idility line work.
3.06 GROUNDING
A. Install grounding electrodes, concrete encased, as indicated on the Drawings.
B . Ground dry-type transformers in accordance with NEC 250 -26 and as indicated on Drawings.
C. Equipment Grounding:
1. Make conduits electrically continuous.
2. Provide insulating grounding bushings on all conduit connections indicated on the Drawings.
3. Provide an equipment ground wire with all feeders to panelboards, transformers, baler,
compactor, parking lot fights, and RTU's.
4. Provide an equipment ground wire with all branch circuits to receptacles and to equipment within
8 feet of floor. Overhead lighting circuits do not require an equipment ground wire.
D. Run insulated equipment ground wires from the ground bar in the serving panelboard to the ground
lug on the equipment served.
END OF SECTION
arer
WM - Lake Elsinore, CA July 16,1993
a
i :,::. : n•e1rt ..va.w,y. r :A <ca.?,- dnito i..sseewu„ner.v ;wr-- .:!.x,.wr.:r.., ,•,,••.., .... ...,... -, •;d'` s, jdbiti::bhtko w atu,d,tA i, e ilrw, .r..,..- ,,Are..Vl.+=.a:.:.•m. r -n.. ,,, . >k: r,xmw. -wt ..,a l....v,nw.H,....raw..e.+.Q.. s.. ...:x. all. i,4w .•:l: -. isdr+r". , . . rw .... .. .. w , os- !,..,...,c.,f rt' +.vna ln... ^ti.. , e£wN+!41. .... ... .....n d' n ?F i:_ ._,.[..,.... i:,,_..,t .:. k,kf.Yil{.i i.itili lwi.
THIS FILM WAS PRWUCSl7 FHOlA)
THE BEST AND MOST COIIPLBTB K
IDP.,AYIROS "AILABLi6 AT THE 4
fIOF i'i I f3
l
rn
Y
a: a:a<•>x+wn..,..l.e..e,awrn.. _....w..,.: -, .. `.r' :y, - ,:::a+ .r _'
t, v'.- -...` ..r, R.rsd'fs;1 .r. 1.., - -
hinged doors having combined lock and latch. Locks shall be icekeyed alike and furnished with two keysyy ,
r• .:.. 'J.; v.u,Y ,., _:;' .- .. v,: tf vKYO ! -.IG. n.?c+,+ui r 1 ,r. :.•. v t y. .., yM• is14 ,rF%!3i'AS- 1,i/d41kML NtiM W:1{96:Ai>3at i.
it
protective covering after assembly of conduit and fittings. Conduit shall not be run in concrete
poured on grade.
urRr -
3.06 WIRE
for each panelboard. 111. Use flexible metal conduit or liquidtight flexible metal conduit for final connections to dry-type 1 A. Make conductor length for parallel feeders identical.
D. Directory Holder: Mount clear plastic cover and metal frame on inside of each door. Mount a legible
transformers, baler, air compressors, HVAC equipment, and motors. i
12. Coordinate installation of conduit in masonry work. B . Lace or clip groups of feeder condu: -tors at distribution centers and wireways. typewritter ^ uit directory properly identifying loEdrs) on each circuit under the clear plastic cover.
Connect chr .;; exactly as indicated on Panel Schedule; no deviation will be tolerated.
1 13. Do not run conduit under slab unless noted by legend on Drawings. All conduit installed below
slab shall be galvanized rigid metal (GRC), or Intermediate metal conduit (IMC). All bends or C. Provide copper grounding conductors and straps.
E. Identification: Each panelboard shall be permanently identified by the symbol indicated on the
Drawings (Sample format: "PANEL HC ") as required by Paragraph 2.01 A.
elbows shall be either GRC or IMC material.
14. Install UL approved expansion fittings complete with grounding jumping where conduits cross
building
D. Use wire pulling lubricant for pulling #4 AWG and larger wire.
expansion joints. Provide bends or offsets in conduit adjacent to building expansion I2.08 SAFETY SWITCHES joints where conduit is installed above suspended ceilings. E. Install wire in conduit runs after concrete and masonry work is complete and after moisture is swabbed
15. Route all exposed conduits parallel or perpendicular to building lines. from conduits.
A. Furnish non - fusible, horsepower -rated safety switches as disconnecting means for motors and fused
16. Allow minimum of 6 inches clearance at flues, and heat sources.
END OF SECTION
safety switches where indicated on Drawings or where required by NEC. Indoor switches shall be 1NEMA1; outdoor switches shall be NEMA 3R Raintight. Switches shall be heavy duty, unless
B . Location:
1. Galvanized Rigid Metal Conduit
i
otherwise noted. Furnish rejection type fuseholders. GRC): Permitted for general exposed or concealed work
above or below grade.
B. Furnish safety switches for HVAC equipment, baler, roadside sign, and other items indicated on the
2. Aluminum Rigid Metal Conduit: Permitted for general exposed or concealed work if installed in
accordance with manufacturer's recommendations. Not permitted embedded in concrete orDrawings.
directly below concrete slab poured on graoa
C. Identification: Identify each switch as required b Paragraph 2.01 A. itY q Y
3. Intermediate Metal Conduit (IMC): Permitted ter general exposed or concealed work above or
below grade.
D. Acceptable Manufacturers: 4. Electrical Metallic Tubing (EMT): Permitted for general exposed or concealed work above
1. Cutler Hammer.
2. General Electric.
grade.
5. PVC Rigid Nonmetallic Conduit (PVC): Permitted for below -grade use outside of building lines,
3. I -T•E. when permitted by governing codes. Install in strict accordance with manufacturer's
4. Square D. recommendations. Conduits penetrating above grade outdoors or penetrating concrete slabs
5 . Sylvania/Challenger. 5.
Westinghouse.
shall be IMC or GRC.
6. Flexible Metal Conduit: Permitted in attic spaces and exposed in lengths of 6 feet or less for
connections to equipment in dry areas. Not permitted for general exposed or concealed work.
7. Liquidtight Flexible Metal Conduit: Permitted in lengths 6 feet less for2.09 FUSES exposed of or
connections to rooftop units, baler, and similar equipment where rigid connections are not
A. Main Panels: Furnish and install fuses by one of the following manufacturers.
suitable.
1. LPS -RK, by 8ussmann.
2. A6D -R, by Gould - Shawmut.
3.03 WIRING DEVICES
3. Litteduse. A. Locate outlets and devices mounted on finished surfaces with regard to paneling, furring, trim, etc.
B . HVAC Equipment Disconnect Switches: Furnish and Install switches by one of the following 1 Where necessary, set the long dimension of the plate horizontally or gang devices in tandem.
manufacturers.
1. FRS -R, by Bussmann.
1 B. Coordinate outlets and devices so as not to detract from the aesthetic effect of the surface in which
2. TRS -R, by Gould- Shawmut. outlets and devices are mounted.
2.10 SUPPORTING DEVICES C. Outlets or devices improperly located or installed shall be repaired or replaced at the Contractor's I I
expense. Outlets and devices shall be set plumb or horizontal and shall extend to, but not project
A. Electrical Equipment Supports: SuSupport electrical equipment with Unistrut Channel, Minerallac Pipe above, the finished surface.
Hangers, or m another • g approved manner where details are not indicated. D. Back -to -back mounting of receptacles, switches, and other wiring devices shall not be permitted.
B . Sleeves: Install conduits passing through concrete floors in galvanized, black steel or Schedule 40
PVC pipe sleeves of adequate size. Sheet metal sleeves shall not be used. Calk sleeves through
E. Mounting Heights: Measure height from finished floor to bottom of device. Comply with the
Drawings heights
outside walls above grade with sealant as specified in Section 07900. regarding mounting of wall switches, receptacle outlets, telephone outlets,
pushbuttons, etc. tf it
C. Plates and Escutcheons: For exposed pipe through walls, floors, and ceilings where exposed to
view, provide chrome - plated floor or ceiling plate of size required. Cutting of openings and
3.04 MOTORS AND MOTOR CONTROLS
Installation of sleeves or frames shall be done In a neat workmanlike manner. A. Make final connection of motors, starters, disconnects, and other items under Division 15 Sections.
D. Conduit Supports: Hangers shall be Unistrut Series P3000 or P3300 channels depending on the load 3.05 SUPPORTING DEVICES
and span Involved. Minerallac Pipe Hangers, Beam Clamps, or Caddy Clips shall be used onlywhereimpracticaltoinstalltheUnistrutHangers. A. Cut openings no larger than required for the Installation; sleeves and/or frames shall be grouted in IE. Anchors, Boits and Screws: Fasten conduit straps, disconnect switches, panelboards, and other place. Surfaces around openings shall be left smooth and finished to match surrounding surface.
equipment secured to walls and slabs with cadmium plated screws or bolts and Ackerman - Johnson
lead cinch anchors, expansion bolts or equal anchors of an approved manufacturer and fitted in holes
B . Flc sleeves in concealed and unfinished locations shall extend one inch above finished floor level.
drilled with the proper size masonry drill. Wood plugs will not be accepted and anchors shall be
in
Ali ier sleeves shall extend approximately 1/4 Inch above the surface or as required to allow for
plac„ment of escutcheons.
properly sized accordance with the manufacturer's recommendations for the load to be supported.
16050.4
16050E 16050 -7
WM - Lake Elsinore, CA
July 16, 1993
WM - Lake Elsinore, CA July 16, 1993 p WM - Lake Elsinore, CA July 16, 1993
T
rn
THIS FILM WAS PRI)DOCSD FROY.'i
TOR BEST AND MOST 0011PLit'1'S::,
DRAWINGS AVAILABLR AT TIM -
r.
In OF FILi IN
Y
a: a:a<•>x+wn..,..l.e..e,awrn.. _....w..,.: -, .. `.r' :y, - ,:::a+ .r _'
t, v'.- -...` ..r, R.rsd'fs;1 .r. 1.., - - r• .:.. 'J.; v.u,Y ,., _:;' .- .. v,: tf vKYO ! -.IG. n.?c+,+ui r 1 ,r. :.•. v t y. .., yM• is14 ,rF%!3i'AS- 1,i/d41kML NtiM W:1{96:Ai>3at i.
it
urRr -
THIS FILM WAS PRI)DOCSD FROY.'i
TOR BEST AND MOST 0011PLit'1'S::,
DRAWINGS AVAILABLR AT TIM -
r.
In OF FILi IN
I
1
WM:
1
SECTION 16500 i09112
1
SECTION 16530 I`
LIGHTING WM: 11232 >
SITE LIGHTING
3tPARTGENERAL ' r
PART 1 GENERAL
1.01 SUMMARY
if
1.01 SUMMARY t
A. Section Includes:
1. Interior lighting fixtures. A. Section Includes:
2. Exterior building security lighting fixtures. 1. Site lighting with underground conduit wiring, terminations, pole foundations, component
3. Circuit and connection to illuminated canopy, automotive, roadside, or mall entrance signs. installation, and system testing. i.
P
B . Work Installed but not Furnished under this Section: 1 B . Work Installed but not Furnished under this Section:
1. Owners lighting suppplier will furnish certain light fixtures as indicated on drawings. Contact
Malmstrom/White Co. at least (4) four weeks prior to desired delivery date, to arrange for
1. Owner's lighting supplier will furnish lighting poles, anchor bolts, fixtures, lamps, and paint.
2. Contractor Is responsible for providing related products required to complete installation.
delivery of Owner furnished items. Attention: Mr. Cedric Williams, (501)224 -2775 or (800)622-
3877. C. Owner will furnish and install illuminated canopy, automotive, roadside, and mall entrance signs.
2. Contractor is responsible for providing related products required to complete installation.
1.02 SYSTEM DESCRIPTION
C. Related Sections:
1. Section 01010 -Summary of Work: General procedures related to Owner furnished products. , A. Design Requirements:
2. Section 16530 - Site Lighting. 1. Poles capable of supporting maximum vertical and horizontal loads exerted on complete
sttru ture in areas having not greater than 120 mph wind design factors with 1.3 wind gust design
1.02 QUALITY ASSURANCE j
A. Fixtures and their electrical components shall bear the UL Label. B . Performance Requirements:
1. The optical system specified herein shall be capable of maintaining a minimum of one horizontal
B. Interior fluorescent light fixtures and ballasts shall be Callfom!a Energy Commission certified. foot candle on areas of paved surface as measured at walking or driving surface based on a 4
fixture mounting style with Type V vertical lamps optics at a mounting height of 42 feet and a
1.03 DELIVERY, STORAGE, AND HANDLING pole spacing of 190 feet.
2. Lighting layout shall produce maximum to minimum uniformity ratio of not more than 5 to 1 and
A. Storage and Protection: Provide proper facilities for handling and storage of materials to prevent average to minimum uniformity ratio of 2.2 to 1 in accordance with IES visual comfort and lighting
damage to edges, ends and surfaces. Keep materials dry, fully protected from weather. safety recommendations.
3. All point- by-point photometric performance test grids shall be based on the following criteria:
1.04 WARRANTY a. Maintenance Factor: 0.75.
b. Mounting Height: 42 feet.
A. Furnish manufacturers standard warranties on products. 1 a Grid: 10 foot centers all points between 4 poles (484 points).
d. Initial lumens 40,000 (each of 4 lamps/poles).
PART 2 PRODUCTS 1.03 SUBMITTALS
2.01 INTERIOR LIGHTING FIXTURES A. Submit the following under provisions of Section 01300.
A. Provide lighting fixtures and lamps as indicated on Drawings. B . Each submittal transmitted for approval shall contain: p
1. Substitutions: No deviations from Lighting Fixture Schedule allowed. 1. Computer prepared photometric layout of proposed lighted area which indicates by
isofootcandle readings the system performance.
B. Verity ceiling and wall details. Furnish fixtures complete with proper mounting arrangements for 2. A photometric report from a national Independent testing laboratory with report number, date,
ceiling or wall construction encountered. fixture catalog number, lum!naire and lamp specifications; IES classification, candlepower
tabulations, zone lumen summary, and isplux plot.
C. Fluorescent Fixtures: 3. UL listing and file number for the specific fixture(s) to be utilized.
1. Ballasts: No deviations from lighting fixture schedule allowed. 4. Pole manufacturer AASHTO calculations indicating the pole and anchor bolts being submitted
2. Where Indicated on Drawings, furnish Protect-A -Lamp covers and caps at surface mounted are capable of supporting the pole and fixture systems being utilized in accordance with
fixtures as manufactured by ALP Lighting and Ceiling Products. specifications.
5. Catalog cuts Indicating complete conformance to the product specification.
2.02 EXTERIOR LIGHTING FIXTURES
1.04 QUALITY ASSURANCE
A. Furnish lighting fixtures and is :ps as indicated on Light Fixture Schedule.
A. Wal -Mart reserves the right to request standard production model fixture samples for inspection and
2.03 EXTERIOR ILLUMINATED SIGNAGE to order such tests as Wal -Mart deems necessary to ensure compliance with these specifications and
to reject those luminaires failing such tests, or those luminaires with Improper or inadequate light
A. Furnish electrical circuits and connections. distribution. Wal -Mart shall be the sole judge as to acceptabllity.
16500-1
16530-1
WM - Lake Elsinore, CA July 16, 1993
WM - Lake Elsinore, CA Ju!y 16, 1993
r -
THIS FILM /JAS PAOOUCED MN
THE BEST AND HO.'3T COHPLSTS
DRAWINGS AVAILABLE AT THE 1.1
6. Ballast and Ballast Housing: Premium type ballast ti.at will provide power for only one metal
halide lamp; capable of providing reliable lamp starting at temperatures as low as -20 °F with
power factor in excess of 90 %; regulating type minus 10% lamp power regulation with ±10%
variation from 480 volt, single phase, input voltage. Ballast assemb y shall be easily accessible
and removable with quick disconnects to the reflector.
7. Lamps: 400 watt, 40,000 lumen, 20,000 hour, clear, supper metalarc by Sylvania.
a. Horizontal Mounted Lamp: Sylvania #MS 400 /140R.
b. Vertical (Base Up) Mounted Lamp: Sylvania #MS 400 /BU.
8. The first row of parking lights adjacent to the building front shall utilize the ten degree tilt -up arms
on those lamps facing the building front and shall be circuited together and labeled "Parking Lot
Security Lighting ".
B . Owner will furnish and erect !Ilu ninated canopy, automotive, roadside, and mall entrance signs.
2.02 FINISH
A. Poles: Factory prime paint poles inside and out and deliver to job site with adequate amount of
TS35B504 black paint to provide two coa' , 5 mil minimum thickness for field applied finish.
B. Fixtures: Ano'ized, baked -on paint or other acceptable material equivalent to #TS35B504 black.
PART? EXECUTION
3.01 SIZING
A. Size feeders to parking lot lights in accordance with following table which is based on 480 volt, 400
watt metal halide lamps, maximum circuit amps and 5% maximum voltage drop to farthest fixture.
There shall be no more than fifteen 400 watt metal halide lamps per 20 arrt4 circuit. There shall be nomorethanten400way! metal halide lamps on the 20 amp circuit with roadsde sign.
Wire Size Schedule: Use the following wire sizes for corresponding distances from panel:
1. 600 Feet: #10
2. 1000 Feet: #8
3. 1600 Feet: #6
4. 2400 Feet: #4
B. For circuit distances more than 2400 feet, size conductors for 5% maximum voltage drop to farthest
fixture.
C . Drawings indicate two 480 vc ", single phase, 20 amp crcults for parking lot lights. If more circuits are
required to comply with Site Lignting Plan and Specification requirements, furnish and Install necessary
additional breakers, contactors, photocells, etc. under this Section of these Specifications.
D. Underground circuits shall have equipment grounding conductors sized in accordance with NEC ( #10
AWG minimum).
E. Parking lot lighting conduit shall be sized in accordance with NEC (3/4 inch minimum).
F. Parking lot light poles rust be grounded If required by local codes.
3.02 INSTALLATION
A. Install pole foundations in accordance with details shown on Drawings.
B. Install poles on concrcie toundations M acardance with details shown on D• :cgs as part of electrical
165303
WM - Lake Elsinore, CA July 16, 1993
0