HomeMy WebLinkAbout31700 GRAPE ST_ 2077 (51)31700 GRAPE STREET 2077 20/30
WAL -MART
B. Label each container with color, type, texture, room locations, in addition to the manufacturers label.
PART PRODUCTS
2.01 MANUFACTURERS
A. Paint: Pittsburgh Paints, by PPG Industries, Inc.
B. Substitutions: Subject to compliance with requirements, one of the following manufacturers may be
substituted for that specified.
1. Devoe & Raynolds Co., Inc.
2. Diamond/Vogel Paints.
3. Dunn Edwards.
4. Frazee.
5. Fuller O'Brian.
6. Glidden Coatings and Resins.
7. Kelly Moore Paints.
8. MAB Paints and Coatings.
9. Pratt & Lambert, Inc.
10. Rodda.
11. Sherwin - Williams Company.
2.02 MATERIALS
A. Paint Accessory Materials: Linseed oil, shellac, turpentine and other materials not specifically
indicated herein but required to achieve the finishes specified of high quality and approved
manufacturer.
B . Paints: Ready - mixed; pigments fully ground maintaining a soft paste consistency, capable of readily
and uniformly dispersing to a complete homogeneous mixture.
C. Paints to have good flowing and brushing properties and be capable of drying or curing free of
streaks or sags.
PART 3 EXECUTION
3.01 EXAMINATION
A. Applicator shall examine areas and conditions under which painting work is to be applied and notify
contractor in writing of conditions detrimental to proper and timely completion of work. Do not
proceed with work until unsatisfactory conditions have been corrected.
3.02 FP.EPARATION
F Clean and prepare surfaces for painting to manufacturers Instructions for substrate to be painted.
3.03 APPLICATIONS
A. Apply each coat at proper consistency.
B. Each coat of paint is to be slightly darker than preceding coat unless otherwise approved by
Wal -Mart Construction Manager. Sand lightly between coals 0 necessary to -ichieve required finish.
C. Do not apply finishes on surfaces that are not sufficiently dry.
D. The number of coats and film thickness required is the same regardless of the application method.
Do not apply succeeding coats until the previous coat has cured as recommended by the
manufacturer.
E. Apply additional coats when undercoats, stains, or other conditions show through final coat of paint
until paint film is of unitorm finish, color, and appearanci. Give special attention to ensure that
surfaces, including edges, corners, crevices, welds, and exposed fasteners, receive a dry film
thickness equivalent to that of flat surfaces.
09900 -2
WM - Lake Elsinore, CA July 16, 1993
F. Minimum Coating Thickness: Apply materials at not less than the manufacturers recommended SECTION 09950
spreading rate. Provide a total dry film thickness of the entire system as recommended by the WM: 07132
manufacturer. WALLCOVERINGS
G. Block Fillers: Apply block fillers to concrete masonry units at a rate to ensure complete coverage with
pores filled. i PART 1 GENERAL
H. Prime Coats: Before application of finish coats, apply a prime coat of material as recommended by i 1.01 SUMMARY
the manufacturer to material that is required to be painted or finished and has not been prime coated
by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed areas in A. Section Includes:
first coat appears, to assure a finish coat with no burn through or other defects due to insufficient 1. Prepare surfaces to receive wallcoverings.
sealing. 2. Adhesive -apply wallcoverings.
I. Pigmented (Opaque) Finishes: Completely cover to provide an opaque, smooth surface of uniform 1.02 REFERENCES
finish, color, appearance, and coverage. Cloudiness, spotting, laps, brush marks, runs, sags, or
other surface imperfections will not be acceptable. A. Federal Specification (FS):
1. FS CC W 408 - Wallcovering -Vinyl Coated. 1. Transparent (Clear) Finishes: Use multiple coats to produce a glass- smooth surface film of even 2. FS L -P 1040 - Plastic Sheets and Strips, Polyvinyl Fluoride (Top Coat).
luster. Provide a finish free of laps, cloudiness, color irregularity, brush marks, runs, sags, orange
peel, nail holes or other surface imperfections. B . American Society for Testing and Materials (ASTM):
J. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or
1. ASTM F 793 - Classification of Wallcovering by Durability Characteristics.
repaint work not in compliance with specified requirements. I 1.03 SUBMITTALS
3.04 MECHANICAL AND ELECTRICAL EQUIPMENT A. Submit the following under provisions of Section 01300.
A. Replace identification markings on mechanical or electrical equipment when painted over or spattered.
1 Area calculations for walloovering quantity requirements including calculated waste.
2. Submit manufacturers literature for recommended adhesives. i 3. Flame Spread rating. e. Paint exposed conduit and electrical equipment occurring in finished areas where it will be exposed
to the public. Color and texture to match adjacent surfaces. 1.04 QUALITY ASSURANCE
C. Paint both sides and edges of plywood backboards for elect,! al equipment before installing A. Certification: Wallcovering and adhesive shall have been tested to provide a U.L. Class "B" fire
backboards and mounting equipment on them. ! hazard classification.
D. Prepaint Gas { iping prior to installation. 1.05 DELIVERY, STORAGE, AND HANDLING
3.05 CLEANING A. Receive, handle, and store materials to prevent damage. After receipt, Inspect all wallcovering to
i
A. work proceeds and upon promptly remove paint where spilled, splashed, or
determine condition.
1. After receipt of walicovering materials, the contractor shall be responsible for replacing all
f work keepspattered. During progress o1 work keep premises free from any unnecessary accumulation of tools, sp damaged materials.
equipment, surplus materials, and debris.
B. Upon completion of work leave premises neat and clean.
B . Store all walloovering in undamaged condition as packaged by the manufacturer, with manufacturers
seals and labels intact.
1. Store all materials flat in a clean, dry area with maintained temperature above 40 degrees F.
3.06 PROTECTION
C. Exercise care to prevent damage during handling and storage.
A. Protect other surfaces from paint and damage. Repair damage as a result of inadequate or
unsuitable protection. D. Take precautionary measure to prevent fire hazards with adhesives and solvents.
3.07
t
PAINTING AND FINISHING SCHEDULE (EXTERIOR) 1.06 SITE CONDITIONS
Paint Schedule provides for minimum two-coat application. Third coat may be required by Wal -Mart A. Maintain areas to receive wallooverin, at a constant minimum temperature of 45 -50 degrees F. for at
Construction Manager to give complete coverage and uniform appearance. Omit primer for items least three days before, and all dwmg, the application period.
shop primed. I 1. Make sure maximum surface moisture conforms to walloovering manufacturers requirements and
j4 surface exhibits negative alkalinity.
Unless otherwise indicated, paint systems scheduled below are by PPG. Systems of similar
performance by other specified manufacturers are acceptable. j B . Provide adequate and continuous ventilation during work and after installation of wallcovering.
A. Ferrous Metal: Solvent Base, Gloss, Modified Alkyd Resin. (including Prepamted Gas Piping,
Sectional Overhead Doors and Hollow Metal Doors and Frames) G PART 2 PRODUC pS
1 st Coat: PPG Speedhide Rust Inhibitive Steel ?rimer (Red or Grey), 6.208 series.
2nd Coat: PPG Speedhide Alkyd Gloss Enamel, 6 -252 series. ( 2.01 MATERIALS
A. Wallcovering material will be furnished by Wal -mart for installation by contractor.
1. Wallcovering:
a. Manufacturer: Sellers & Josephson "Skye" #899 -8123.
699003 ( 09950 -1
WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993
r. r,..,.,•,,r,,,. r etw+ m... }.ax cosy...,.y., 4 W, fi .. -- ,. -.....
n., <.::N<t..ya.K Ai. Nn:.l i •.+.f .DMk .V.ivr aa,s a., t_".a1 r t _+m- i,t..Mr434 I M...F.:WiKar flt "". - .. .y/, d <. , L.. =i". =-V Fti h '
a7.'¢<..\ . .r... rr a^is'h =a. <. t+U.f •i, kqn ++cowl, «.;k:MF, J<•T.cwweYU.%ilMa' +' "rW/f ', .•N .
THIS FILM WAS PRWUCSD FRaU.i','
TM BEST ARD "T 00UPIRTS
DJUVIINCTi! :1V.VAI,A3I,S AT Talc
n
PART 2 PRODUCTS B. Apply, trowel, and float filler to achieve smooth, flat, hard surface. Use only fillers which are
acceptable to coating manufacturer. Grind irregularities above the surface level. Prohibit traffic until
2.01 MANUFACTURERS filler is cured.
A. Subject to compliance with requirements, provide special flooring system of one of the following C. Vacuum clean substrate.
manufacturers:
1. LockSh;eld System, by Ameron Protective Coatings Division, Brea, CA. (800)344.0025 D. Water-cured concrete must be cured a minimum of 14 days and have attained 80 percent of its final
2. Nitoflor System, by Fosrock, Plainview, NY. (u00) 645 -3954. strength. Prepare surface in accordance with ASTM D4259 or ASTM D4260 with muriatic acid using
equal parts of acid to water by volume.
B . Substitutions: None accepted. 1. Concrete surfaces cured with conventional curing compounds or contaminated with form oils must
be completely cleaned by ASTM D4259. Clean concrete surfaces by abrasive blasting per2.02 LOCKSHIELD SYSTEM ASTM 4269. Acid etching is not acceptable, as it will not sufficiently remove these contaminants.
A. Curing Compound (optional): Nu -Klad 105A epoxy primer and sealer, by Ameron. E. Concrete Curing: New concrete which has been cured with the approved curing compound specified
herein, will not require blasting or etching. Remove fins and projections from concrete surfaces, and
B . Epoxyy Coating: Amerlock 400 epoxy, by Ameron.
1.
ensure that surfaces are free from oil and other contaminants.
Color: OSHA Safety Red, RD -2 red. 1. Apply to slabs immediately after final finishing operation or upon disappearance of the "bleed -
2. Color: OSHA Safety Yellow. water sheen" of surface moisture.
2. Prior to application of subsequent coats of epoxy, water and detergent wash for dirt, oil and
C. Polyurethane Coating: Amershield Aliphatic Polyurethane, by Ameron.
1. C, 3HA
grease removal.
Safety Red, RD -2 red.
2. Color. OSHA Safety Yellow. 3.04 PRIMER APPLICATION
D. Non -Skid Additive: Amercoat #886, by Ameron. Pumice additive, 2 pints per gallon of polyurethane A. Primer coat is required for Nitoflor System only.
coating.
B. Prime property prepared concrete surface with Nitoflor primer in strict accordance with manufactures s
2.03 NITOFLOR SYSTEM instructions. Allow to cure for 24 hours before proceeding.
A. Primer: Nitoflor FC 140 , thinned 50% by volume with Solvent 102, by Fosroc. 3.05 EPDXY COATING APPLICATION
A. Primer (California): Nitoflor FC 130E Epoxy Primer (water base), by Fosroc. A. Prepare epoxy components in accordance with manufacturers instructions. Use manufacturer's
spec fied mixing ratios. Thoroughly mix resins and cure components until uniformly blended to aB. Epox6 Coaling: Nitoflor FC 140, full strength, b Fosroc. y workable consistencyh. Do not mix more material than can be used within the expected pot life. Do
W
Wal-Mart ".
when time has gone past the recommended pot life. not eDryfi2.. Color: OSHA Safety Yell
material
B . Epoxy Coating (California): Nitoflor FC 130E Color Coat (water base), by Fosroc. (Full strength B. If thinning is necessary, add thinners in strict accordance with coating manufacturer's instructions.
application.)
1. Color: "Wal-Mart Red ". C. Maintain optimum application temperature range.
2. Color: "Wal -Mart OSHA Safety Yellow ".
C. Polyurethane Coating: Nitoflor UR512 Urethane, by Fosrcc.
D. Apply epoxy coating in wet even coats, with 50 percent overlap to avoid holidays, bare areas and
pinholes. Ensure that the surface is completely and uniformly coated without thick or ponded areas
1. Color: "Wal -Mart Red ". which will adversely affect curing.
2. Color: "Wal -Mart OSHA Safety Yellow ".
E. Ventilate confined areas with clean air between coats and while curing the final coat. Maintain surface
D. Non -Skid Additive: Pumice additive, 2 pints per gallon of polyurethane coating, as recommended by I temperature at least 5 degrees F above dew point to prevent moisture condensation between
Fosroc. coats.
F. Repair damaged areas by brush or spray.
PART 3 EXECUTION
3.06 POLYURETHANE COATING APPLICATION
3.01 ACCEPTABLE INSTALLERS
A. Prepare urethane components in accordance with manufacturers Instructions. Use manufacturer's
A. A. pproved Ameron Applicators: specified mixing ratios. Thoroughly mix resins and cure components until uniformly blended to a1ParpartCorporation, 3200 S. 6th Street, Lincoln, NE 68502, (402)423 -2545. Lynn Parpart, or workable consistency. Do not mix more material than can be used within the expected pot life. Do
Ben Parpart. not apply material when time has gone past the recommended pot life.
2. Pro -Tech Coatings, Inc., 1920 Stedman, St. Louis, MO 63114, (314)427 -8644. Mark Seibel. 1. Dry film thickness: 5 mils.
3. CCS Flooring, Inc., 524 Morse Avenue, Schaumberg, IL 60193, (708)893 -0901. Grant Johnson,
Jr. I B . Thin only as required for workability. If thinning is necessary, add thinners in strict accordance with
4. Grave Johnson Co., 2218 University Ave., S.E., Minneapolis, MN (612)J79 -2825, (612)379 -0907 coating manufacturer's instructions.
FAX, Gary Trimm.
5. Advanced Coatings Designs, 2605 Temple Heights, Suite F, Oceanside, CA 92056, (619)631- C. Maintain optimum application temperature range, in order to prevent condensation.
5070(619)630 -7636 fax, Stacey Ingram. i6. Beugler Industrial Flooring, P.O. Box 6232, Concord, CA 94524, (510)439.0197 ' . D. Apply urethane coating in wet even coats, overlaping each pass 50 percent. 7. Howard & Wills Contracting, Inc., 317 Salem Drive, Owensboro, KY 42301, (502)685 -3023.
502)684 -3688. Steve Wills
09700-2 ? 09700-4
WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993
F •
7 Ci'.aiKwv`.",Yw's„ria"'` °' F'°++ .. i:"w7`J:"w`.`ii:'•','"a..°lu. .. - _ - ., a.•..a,> :•:
s.,,,
c.. .hH<s: c,x, r i•MV$w.w,.wsfpyinv +N,. 'M K ai xuaSR •n+e 3 y.
TRIO FIId! 11AB PWDUCM I"
THE BEST AM MOOT cullu% TS
UOOINGS AVAILABLE AT THE
TIVE OF FILYI
JF
SECTION 09780
WM: 05202
FLOOR TREATMENT
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Application of stripper, sealer, and finish to tile specified in Section 09650,
1.02 QUAuTY ASSURANCE
A. Stripper Crew Requirement: Four -man crew; one to apply solution ahead of buffer, one to run
slow -speed buffer, two with mops and buckets to pick up dirty solution behind buffer and rinse floor
prior to applying sealer and finish.
PART PRODUCTS
2.01 MATERIALS
A. Stripper: Bravo Stripper, by Johnson Wax.
B. Sealer: Over and Under Resilient Tile Sealer, by Johnson Wax.
C. Finish: Sprint Floor Finish, by Johnson Wax.
D. Substitutions: None accepted.
2.02 EQUIPMENT
A. Use the following equipment to perform work of this Section:
1. One automatic floor scrubber (with full charge.)
2 Two or three side -to -side slow speed buffers.
3. Five black stripping pads.
4. Five buckets with wringers.
5. Six mop head and handles. Soak new mops for 24 hours.
6. Two clean dust mops.
PART 3 EXECUTION
3.01 PREPARATION
A. Stripping should not commence for a week or more after installation of tile to ensure that tiles are
laying flat and are fully adhered to the substrate.
3.02 STRIPPING
A. Dust mop entire sales floor and remove gum, tar, glue, etc. from floor.
B. Mix one part Stripper to four parts hot water.
C. Dip mop in stripping solution, let excess solution drain off, and apply stripper to floor. Let stripper
set on floor five minutes before scrubbing. Do not allow stripper to dry on floor.
D. Important: With black stripping pad under the slow speed buffer, pass over each tile section at least
twice. Do not rush this procedure; it is crucial.
E. After a section is stripped, pick up the stripping solution Immediately with wet vacuum.
F. Rinse thoroughly by mopping with clear water, removing remaining solution, finish, and dirt. Use wet
vacuum for water pickup.
09780 -1
WM - Lake Elsinore, CA July 16,1993
Y
G. Move stripping operation to next area of sales floor and repeat the procedure.
H. Let floor dry completely.
3.03 SEALING
A. Apply 2 coats of specified sealer in strict accordance with manufacturer's instructions.
3.04 FINISHING
A. Pour specified floor finish into clean mop buckets.
B . Prepare new or clean mop for appl ing floor finish.
C. Dip mop in floor finish, place mop in wringer and tap lightly. The mop should be full bu! not
dripping. g•
D. Apply two coats of specified finish to floor. Under normal conditions, allow a minimum of 45 minutes
drying time between coats.
E. Important: Air conditioning or heat must be in operation to assure adequate drying time and curing of
finish between coats.
END OF SECTION
i
1'
09780.2
1 +
WM - Lake Elsinore, CA July 16, 1993
I
WM:
SECTION 09800
SPECIAL COATINGS
04093
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Masonry Weatherproofing System: Cementitious and Acrylic waterproofing coatings and
decorative acrylic finish coat systems.
B. Related Sections:
1. Section 04220 - Concrete Unit Masonry: Exterior masonry walls to receive weatherproofing
system as indicated on drawings.
2. Section 09900 - Painting: First coat to include area of blue and red accent bands.
1.02 REFERENCES
A. American Society for Testing and :Aatedals (ASTM):
1. ASTM D968 - Abrasion Resistance of Organic Coatings by the Falling Abrasive Tester.
2. ASTM D822 - Operating Light and Water Exposure Apparatus (Carbon Arc Type) for Testing
Paint, Varnish, Lacquer, and Related Products.
3. ASTM G26 Operating Light- Exposure Apparatus (Carbon Arc Type) With and Without Water
for Exposure o Nonmetallic Materials.
B. State of Alabama Highway Department Specifications for Freeze -Thaw Tests on Concrete Coating
Material for Bridge Finishes.
1.03 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B. Product Data: Submit in letter form, the manufacturer and colors selected.
1.04 QUALITY ASSURANCE
A. Applicator Qualifications: Properly trained and approved by the weatherproofing system
manufacturer and have authorization to offer specified warranty. Submit installer letter of certification,
signed by Technical Representative of system manufacturer.
B. Field Sample:
1. Apply masonry weatherproofing system to sample precast concrete panel.
2. Reflect proposed color, texture, and workmanship.
3. Obtain acceptance of completed panel from Construction Manager before beginning work.
4. Retain accepted panel during construction as a standard for judging completed work. Do not
after, move, or destroy panel until work is completed.
C. Pre - installation Conference:
1. General Contractor shall range meeting no less than seven days prior to starting work.
2. Attendance:
a. General Contractor.
b. Coating subcontractor.
a ArchftecVOwnees Representative.
d. Coating manufacture representative /distributor.
3. Agenda:
a. Substrate condition.
b . Sequence and method of application of coating system.
1.05 PROJECT CONDITIONS
A. Environmental Requirements:
1. Do not apply on frozen or frost - filled surfaces.
2. Do not apply 0 temperature is below 40 °F or expected to fall below 40 °F within 24 hours.
3. Protect material from freezing.
09800.1
WM - Lake Elsinore, CA July 16, 1993
PART EXECUTION
3.01 EXAMINATION AND PREPARATION
A. Allow 28.30 days for curing of concrete /mortar.
B. Examination:
1. Examine substrate to which finely textured coating is to be applied. Do not proceed if
unsatisfactory conditions exist which hamper p,-oper application.
2. Beginning of application means acceptance of substrate condition.
C. Preparation:
1. Surfaces to receive system shall be free of defects such as honeycombs, form marks, tie holes,
concrete droppings, laitance, dirt, dust, grease, form release treatments, efflorescence, curing
compounds, paint and any other foreign material.
2. Fill holes in excess of 3/8 inch.
D. Beginning of application means acceptance of substrate.
3.02 APPLICATION
A. General:
1. Begin system application at rear of buildinand work toward front. Begin application of system
in the presence of manufacturers Technical Representative.
2. Sealer or filler: Apply in accordance with manufacturers recommendations.
3. Decorative Acrylic Coating:
a. Apply material at a rate recommended by manufacturer.
b. Apply material by brush, roller, plaster type sprayer, or low pressure sprayer.
a Back roll brushed or sprayed material; cross roll roller - applied material.
d. Finish material so that brush and roller strokes are in one direction.
B . Application (Thorn System Products) Cementitious Block filler:
1. Dampen wall prior to and during application. Change of color of masonry unit should be noted.
Do not soak wall excessively or allow water to accumulate on the surface.
2. Apply brush, plaster type or airless sprayer coat of Cemenlitious Block Filler to the surface of
flat, split - faced, rock -faced or fluted masonry units. One unit of cementitious block filler (5.6 gals)
will cover 600.750 sq ft of flat faced CMU; 350 -500 sq It of split - faced, rock faced and fluted
CMU. Using plaster type sprayer, spray -apply at 35 -40 PSI air pressure at spray nozzle, using
a 3/16" or 1/4 spray orifice.
3. Using a wet clean soft nylon bristled brush or broom, work the fill coat In a horizontal direction to
fill pores. Lay off fill coat in a vertical direction. Do not allow brush or broom to become loaded
with material. Backroll surface with 3/4" nap roller using downward finish strokes to remove any
brush strokes. Do not let material set or harden before backrolling.
4. Finish from breakpoint to breakpoint. Do not stop in middle of wall.
5. If hot, dry and windy conditions exist, let fill coat set for 24 hours, cure by fog spraying on
second day if conditions are hot dry or windy.
6. Decorative Acrylic Coating:
a. Stir Thorocoat thoroughly with mechanical mixer to assure complete, uniform dispersion
throughout.
b. In extremely hot, dry weather, slight damping of the surface with clean, potable water is
acceptable prior to applying Thorocoat- Smooth.
a Apply Thorocoat- Smooth by roller, plaster or low pressure sprayer at a rate not to exceed
80 square feet per gallon.
d. Finish material so that roller strokes are in one direction.
C. Tolerances: Finish coat must be pinhole free.
3.03 FIELD QUALITY CONTROL
A. All exterior masonry surfaces shall receive complete and thorough coverage or specified masonry
weatherproofing system in colors as scheduled on Drawings.
B. Maintain schedule of application of system in field office for Owners review.
098003
WM - Lake Elsinore, CA July 16, 1993
Ii YRrr!maw... ... -vw....
a... .u....r.,a en•.. .
7
THIS FILM WAS PHMTJCZD FM rj
THE SINST AND MOT COMIPI+STE
DRAWINGS AVAH ADIal AT THS
q % TI OF F"ING. k;ry•
B. Galvanized Metal (includes garden center canopy): Solvent Base, Gla;r; Alkyd -Resin Enamel.
B. The
E. Hang smooth, non - matching patterns by pasting strips on the wall, overlapping the edges, and
double- 1st Coat: PPG Speedhide Galvanized Steel Primer Intsrior /Exterior, 6.209 series. contractor shall provide all wall primer, sealer and adhesive as recommended by the wallcovering
manufacturer.
cutting" through both thicknesses.
2nd Coat: PPG Speedhide Gloss -Oil Interior /Exterior- Interior Enamel, 6.252 series. 1. Use a 0.04" or 0.06" zinc or aluminum strip between wall and material when cutting, to avoid
Paint inside surfaces of guttering. gouging the wall.
2.02 ADHESIVES
C. Exterior Insulation and Finish System: Water Base, Flat, Vinyl Acrylic. i F. Use a stiff- bristled brush or flexible broad knife to eliminate air pockets and to secue the
1st Coat: PPG Speedhide Acrylic Latex House Paint, 6.650 series. A. Manufactured products recommended by wallcovering manufacturer for used in applying their specific wallcovering to the wall surface.
2nd Coat: PPG Speedhide Acrylic Latex House Paint, 6 -650 series. product. j
I G. Fill spaces above and below doors and similar areas in sequence from the roll, not later when all full -
D. Concrete Unit Masonry (Accent Stripes): Water Base, Semi - Gloss, Viny. Acrylic Latex. B. Do not use wheat paste or cellulose paste with vinyl wallcoverings. length pieces have been installed.
1st Coat: Special Coating per Section
2nd & 3rd Coat: PPG Interior /Exterior Waterater Base Semi-Gloss Enamel, 5-010 series. s C. Do not thin adhesives. I H. Remove excess paste from each seam as it is made and before proceeding to next .seam. Use
Back roll both paint coats as required to ensure good coverage. sponge dampened with plain warm water, but not wringing wet. Wipe seam clean with dry cloth
f towel.
3.08 PAINTING AND FINISHING SCHEDULE (INTERIOR) PART EXECUTION
I. Examine each seam carefully when completed. Trim additional selvage where required to achieve a
A. Ferrous Metals: Solvent Base, Lo- Lustre, Alkyd pdResin. (Hollow Metal Dears and Frames, Pipe 3.01 EXAMINATION color and pattern match at seams.
Bollards, Stair Stringers, and Handrails.)
1 st Coat: PPG Speedhide Quids -Drying Machinery and Equipment Primer 6 -205. A. Examine area in which work is to Lott performed. Report in writing to tho architect all prevailing J. Wrap wallcovering 6" beyond outside corners and 3" at inside corners.
2nd Coat: PPG Speedhide Low Odor Interior Enamel Wall and Trim Lo-Sheen .011, 6 -90 series. conditions that may adversely affect satisfactory execution of this Work. Do not proceed with work 1. Cutting at corners will not be accepted.
until unsatisfactory conditions have been corrected. 2. Horizontal seams will not be accepted other than as indicated or required for pattern change.
B. Gypsum Board: Water Base, Eggshell, Latex Enamel. 1. Make sure surfaces to receive wallcovering are clean, true, and frea of irregularities.
1st Coat: PPG Speedhide Quick -Drying Interior Latex Primer - Sealer 6 2 series.
2nd Coat: PPG Speedhide Latex Eggshell Enamel, 6.411 series. B Schedule installation of wallcovering as late as to damage during
K. Install wallcovering to extend from 2" above finish floor to ceiling line or above. Wallcovering shall be
possible prevent construction and
movement of materials.
secure, smooth, clean, without wrinkles, gaps and overlaps at completions of work.
C. Wood (Stained): Clear Varnish over Oil Stain. 3.04 CLEANING
1st Coat: "Cape Cod Grey" stain, to match wall paneling by Olympic Stain. Fill wood with natural
filler tinted before final finis h.
C. Starting work constitutes acceptance of the existing conditions and responsibility for correcting all
unsatisfactory and defective workpastewoodwithoilstain encountered. A. Clean wallcoverings of all adhesives, dust, dirt, and other contaminants.
2nd Coat: Rez Varnish, Alkyd Gloss Interior Clear, 77.4 series.
3rd Coat: Rez Vamish, Interior Satin Oil Clear, 77.7 series. 3.02 PREPARATION { B . Remove debris and leave ar9a in neat and clean condition.
D. Wood (Stockroom Shelving): Clear sealer only. A. Surface to receive wallcovering shall meet the minimum requirements established by the wallcovering 3.05 PROTECTION
1 st Coat: PPG Speedhide Quick -Drying Interior Sanding Wood Sealer and Finish (clear), 6 -10 series. manufacturer.
A. Protect finished work installed by other trades prior to work under the Section. Replace all work
E. Concrete Unit Masonry (Sales Areas): Water Base, Eggshell, Vinyl Acrylic Latex. B . Gypsum wallboard substrate shall have all fasteners recessed, with all joints and fastener damaged by workmen of this trade without additional cost to Wal -Mart.
1 st Coat: PPG Speedhide Masonry Block Filler, 6 -7 series.
2nd 6 3rd Coat: PPG Speedhide Eggshell Latex Enamel, 6
depressions taped, speckled and sanded. The surface to receive wallcovering shall be uniformly
level and ! 411 series.
Back roll both filter and paint coats to ensure good coverage.
smooth.
1. Fill nicks, gouges, and other minor Imperfections of substrate surfaces with latex filler. Sand
END OF SECTION
3
smooth flush with surf ace.
F. Concrete Unit Masonry (Stockroom area): Water Bas,, Eggshell, Vinyl Acrylic Latex. 2. Follow wdti prime coat of sealer recommended by wallcovering manufacturer.
1st Coat: PPG Speedhide Masonry Block Filler, 6 -7 series.
2nd & 3rd Coat: PPG Speedhide Semi -Gloss Latex Enamel, 6 -510 series. C. Painted Surfaces: Wash down painted surfaces with idsodium phosphate, rinse with clear water.
Back roll both filler and paint coats to ensure good coverage. , i
j
Open up glossy surfaces with rough sandpaper for bond, then seal.
1. Remove bleeding paint, flaky paint, and woad stain.
G. Concrete Unit Masonry (Automotive Areas): Water Base, Gloss, Vinyl Acrylic Latex.
1 st Coat: PPG Speedhicle Masonry Block Fillor, 6 -7 series. D. Metal Surfaces: Remove rust, dirt, and grease. Prime with recommended metal primer. I2ndA3rdCoat: PPG Interior /Exterior Water Base Gloss Enamel, 53 -610 series.
3 ;;c4 roll both filler and paint coats to ensure good coverage. E. Sizing: Size all walls prior to installation in strict accordance with manufacturer's printed instructions.
H.
r
uocrete Floors: Alkyd and Chlorinated Rubber, Flat, OSHA Yellow. ) F. The contractor shall be responsible for all defects In the substrate which appear in the finish surface
Primer: None j after completion. ffinish: 2 coats, MWF 5.0 miss. Pittsburgh Traffic and Zone Marking Paint 11 line.
3.03 INSTALLATION j
END OF SECTION
A. Remove hardware, accessories, plates and similar items to allow fabric to be installed. Upon
completion of each space, reinstall all items removed.
B . Prime and seal substrates per wallcovering manufacturer's recommendations for the type of substrate
being covered. A
C. Follow the adhesive manufacturers directions for mixing ano applying adhesive.
D. Use wallcovering panels in the exact order as they are cut from rolls; use olls in consecutive order. {
r
Apply paste to the back using a roller or paste brush. !
i t
1YJ900-4 j 09950.2 09950,3
1
WM - Lake Elsinore, CA Juty 16, 1993 WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993
4'1MR'fSfy'!rLr4 .r,. .'
9 c Lv...HP. . ES- IrfO W. f. i^ r>•' AI MHaY+ HI WC+ buVAYa,? °W,VW'!„n,^yr3 S??IMAi!C"E 7! Yee! s1r :.Y:.,Jfi_.N ??t.:wJ.!.,:J::T. Sit. r...^ wi...:«.:. .^..tAu}i!I i}A rt,e".".aa "',L'i.CiM+Y B%1,s 1Iri11w'6, ''IdSi{
SiYF
Yi'Y^ bYiw_ _'
A. *S
TSIa FILM! WAS Powum "M
Tsa BEET AN WT CONK,s$
LMNINGS "AILABLS AT Tim
TI OF i'ILYI
fl
MIMT' "wI V • -. w r, f rwOM•' IYS` °.`w.r'.gwwww_1, .
THIS FILM WAS PRODDCBD FROM
THE BEST AND MOST COMPUTE
DRAWINGS AVAILABLE AT TBB
TINS
WOF
FILM„„s.
SECTION 09900
WM: 061893
PAINTING
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Paint and finish interior and exterior exposed surfaces.
2. Include field painting of exposed pipes and ducts, hangers, exposed steel and iron work, and
primed metal surfaces of equipment installed under Mechanical and Electrical Sections.
3. Above roof items including, but not limited to satellite support steel, roof hatch, inside surfaces
of gutters sheet metal counterflashing and top surfaces of front and Garden Center canopy
supporting steel.
B. Items Not Painted:
1. Aluminum, brass, bronze, stainless steel, and chrome plated steel.
2. Pre - finished items, such as toilet compartments and acoustical ceiling materials.
3. UL, FM and other code - required labels.
4. Equipment identification, performance rating, or name prates.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B . Product Data: Submit on Product Compliance Letter, the manufacturers, paint color names and
numbers selected.
C. Samples: Exterior only; color and manufacturer.
1. Submit two 12x12 Inch hardboard samples of each color and texture. Resubmit unti! color,
texture, and sheen are accepted.
2. For masonry, provide two 4 inch squares of masonry for each type of finish and color. Indicate
filler, primer, and finish coats.
3. If directed by Wal -Mart Construction Manager, duplicate painted finishes of acceptable samples
on actual wall surfaces for further acceptance.
1.03 DELIVERY, STORAGE, AND HANDLING
A. Deliver paint materials In sealed original labelled containers, bearing manufacturer's name, type of
paint, brand name, color designation, and Instructions for mixing and/or reducing.
B. Provide adequate storage facilities. Store paint materials at minimum ambient temperature of 45 °F in
well -,ntilated area.
C. Take precautionary measures to prevent fire hazards and spontaneous combustions.
1.04 ENVIRONMENTAL REQUIREMENTS
A. Apply paint finishes only when moisture content of surfaces is within acceptable ranges for type of
finish being applied.
B. Ensure surface temperatures or surrounding air temperature is above 40 °F before applying alkyd
finishes; above 45 °F for interior latex, and 50 °F for exterior latex work. Minimum for varnish and
transparent finishes is 65 °F.
C. Provide adequate continuous ventilation and sufficient heating facilities to maintain temperatures
above 45 °F for 24 hours before, during and 48 hours after application of finishes.
1.05 EXTRA MATERIALS
A. Furnish the following, to Wal -Mart, under provisions of Section 01700.
1. Provide 2 gallons of each color for the Pharmacy area.
2. Provide 5 gallons of each color, type and surfacte texture for general sales area.
09900-1
WM - Lake Elsinore, CA July 16, 1993
0
4. Protect surfaces from rapid drying where windy, hot, and dry conditions exist. 3.04 COLOR SCHEDULE
5. Protect from precipitation for 24 hours after application.
6. Avoid applying material during rapid and extreme changes in temperature to prevent thermal A. Lt. Grey:
shock cracks during the curing process. 1. "Early Dawn" (NAM -034), by Thom System Products.
7. The following condi.. -,may require damping the surface prior to and during application: 2. "Dover Grey" (014 -56P), by Sonneborn Building Products.
a. Wind - caused re,.,u drying of surface.
b. Excessive s,urfacetemperature. B. Dk. Grey:
a Excessive air temperature. 1. "Bagdad Grey" (NAM -306 , by Thom System Products.
d. Direct sun. 2. "Drum Hill Grey" (Q15 191, by Sonneborn Building Products.
e. Low humidity.
END OF SECTION
1.06 WARRANTY
A. Provide five year material and labor warranty to cover: j
1. Waterproofing above grade. J
2. Bonding.
3. Weathering.
B. Manufacturers "Intent to Warrant" must be issued to the General Contractor and Wal -Mart before
application commences.
PART2 PRODUCTS
2.01 MANUFACTURERS
A. Subject to compliance with requirements, provide coatings of one of the following manufacturers:
1. Thom System Products.
2. Sonneborn Building Products.
B. Substitutions: None accepted.
2.02 COATINGS
3
A. Cementitious Coatings, by Thom System Products:
1. Cementitious Block Filler: Cemerditious, acrylic - modified waterproofing block filler, made from
the following components.
a. Super Quickseal - White.
b. Thorosheen.
a Water.
2. Decorative Acrylic Coating: Thorocoat- Smooth, by Thom System Products.
3. Colors: As indicated on drawings.
7i
B. Acrylic Coatings, by Sonnebom: Hydrocide Colortlex by Sonneborn Building Products.
1. Block Filler: Colorfiex Block Filler 0749 for system, by Sonneborn Building Products, as
j
required by system manufacturer for warranty.
2. Colors: As Indicated on drawings.
2.03 MIXES i
A. Mix in strict accordance with printed Instructions of manufacturer. Use approved mechanical mixer.
Do not use frozen, caked, or lumped materials. Clean mechanical mixers and containers after each
mixing: keep batch free of material and sealers from previous mixes. j
B . Mixing (Thom System Products): "One unit" of cementitious block filler shall be mixed as follows.
7
1. Mix one 50 lb. bag of Super Quickseal together with 12 to 16 quarts of clean, potable water
until a creamy batter consistency is achieved, with uniform color. Hot temperatures and low
humidity will require maximum amount of water to achieve the creamy consistency.
2. Let mat, lal set for five to fifteen minutes to soak, then temper back by adding one (1) gallon of
Thorosheen -Tint Base.
C. Mixing ( Sonnebom Building Products): Mix in strict accordance with manufacturer's published
instructions.
t
f
09800.2 09800.4 »
WM - Lake Elsinore, CA July 16,1993 WM - Lake Elsinore, CA July 16,1993
r
MIMT' "wI V • -. w r, f rwOM•' IYS` °.`w.r'.gwwww_1, .
THIS FILM WAS PRODDCBD FROM
THE BEST AND MOST COMPUTE
DRAWINGS AVAILABLE AT TBB
TINS
WOF
FILM„„s.
SECTION 09900
WM: 061893
PAINTING
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Paint and finish interior and exterior exposed surfaces.
2. Include field painting of exposed pipes and ducts, hangers, exposed steel and iron work, and
primed metal surfaces of equipment installed under Mechanical and Electrical Sections.
3. Above roof items including, but not limited to satellite support steel, roof hatch, inside surfaces
of gutters sheet metal counterflashing and top surfaces of front and Garden Center canopy
supporting steel.
B. Items Not Painted:
1. Aluminum, brass, bronze, stainless steel, and chrome plated steel.
2. Pre - finished items, such as toilet compartments and acoustical ceiling materials.
3. UL, FM and other code - required labels.
4. Equipment identification, performance rating, or name prates.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B . Product Data: Submit on Product Compliance Letter, the manufacturers, paint color names and
numbers selected.
C. Samples: Exterior only; color and manufacturer.
1. Submit two 12x12 Inch hardboard samples of each color and texture. Resubmit unti! color,
texture, and sheen are accepted.
2. For masonry, provide two 4 inch squares of masonry for each type of finish and color. Indicate
filler, primer, and finish coats.
3. If directed by Wal -Mart Construction Manager, duplicate painted finishes of acceptable samples
on actual wall surfaces for further acceptance.
1.03 DELIVERY, STORAGE, AND HANDLING
A. Deliver paint materials In sealed original labelled containers, bearing manufacturer's name, type of
paint, brand name, color designation, and Instructions for mixing and/or reducing.
B. Provide adequate storage facilities. Store paint materials at minimum ambient temperature of 45 °F in
well -,ntilated area.
C. Take precautionary measures to prevent fire hazards and spontaneous combustions.
1.04 ENVIRONMENTAL REQUIREMENTS
A. Apply paint finishes only when moisture content of surfaces is within acceptable ranges for type of
finish being applied.
B. Ensure surface temperatures or surrounding air temperature is above 40 °F before applying alkyd
finishes; above 45 °F for interior latex, and 50 °F for exterior latex work. Minimum for varnish and
transparent finishes is 65 °F.
C. Provide adequate continuous ventilation and sufficient heating facilities to maintain temperatures
above 45 °F for 24 hours before, during and 48 hours after application of finishes.
1.05 EXTRA MATERIALS
A. Furnish the following, to Wal -Mart, under provisions of Section 01700.
1. Provide 2 gallons of each color for the Pharmacy area.
2. Provide 5 gallons of each color, type and surfacte texture for general sales area.
09900-1
WM - Lake Elsinore, CA July 16, 1993
0
I
I
WM:
SECTION 10165
09242 SECTION 10800
PLASTIC LAMINATE TOILET COMPARTMENTS
WM: 05202
TOILET AND BATH ACCESSORIES
PART GENERAL PART1 GENERAL
1.01 SUMMARY 1.01 SUMMARY
A. Work Includes: A. Section Includes: 1. Plastic laminate toilet compartments, floor mounted, head rail braced. 1. Toilet accessories and attachment hardware. 2. Urinal screens, wall mounted.
3. Attachment hardware. 1.02 REFERENCES
4. B. Ralated Sections:
1. Section 06200 - Finish Carpentry: Framing and plates within walls. Coordinate plastic laminate
A. American National Standards Institute (ANSI):
1. ANSI Al 17.1 - Specifications for Making Buildings and Facilities Accessible To and Usable byselection.
2. Section 10800 - Toilet and Bath Accessories: Coordinate compartment installation with Physically Handicapped People.
subsequent accessory installation. 1.03 SUBMITTALS
1.02 REFERENCES A. Submit the following under provisions of Section 01300.
A. ANSI A117.1 - Safety Standards for the Handicapped. B . Product Data: Submit in letter form through General Contractor to Wal -Mart Construction Department
1.03
1
SUBMITTALS the manufacturer and model selected.
f A. Submit the following under provisions of Section 01300, PART 2 PRODUCTS
B. Product Data: Submit on Product Compliance Letter the manufacturer and model selected. 2.01 MANUFACTURERS
iPART 2 PRODUCTS
A. Subject to compliance with requirements, provide toilet accessories of one of the following:
1. Bradley Corporation, Washroom Accessories Division, Laurel, NJ, (609)235.7420.
2.01 TOILET COMPARTMENTS 2. American Specialties, Inc., Yonkers, NY, (914)476 -9000.
3. Bobrick Washroom Equipment, Inc., North Hollywood, CA, (818)764 -1000.
A. Subject to compliance with requirements, provide toilet compartments of one of the following
4. A. 6 J. Washroom Accessories, Windsor, NY, (914)565 -3050.
5. McKinney /Parker, Scranton, PA, (717)346.7551. manufacturers:
1. Concord, by Accurate Partitions Corp.
6. Tubular Specialties Mfg., Inc., Los Angeles, CA, (213)515.4801.
2. Type HB, by All American Metal Corp. ( AAMCO)
3. Type PL -FF, by American Sanitary Partition Corp. B. Substitutions: None accepted.
4. Overhead braced, by AMPCO Products, Inc. 2.02 MATERIALS5. Series 40, by General Partitions Mfg. Corp.
6. Embassy, by Global Steel Product-, Corp. A. Stainless Steel: AISI Type 302/304. 7. Metropolitan, by Knickerbocker Partitions Corp.
8. Corinthian Type FP -500, by Metpar Steel Products Corp.
9. Overhead Braced, by Weis/Robart Partitions Inc.
B . Mounting Devices: Hot -dip galvanized after fabrication or of same material as accessory unit.
B. Urinal Screens: Wall hung type, 24" x 42" to match toilet compartments. t C. Adhesive: Epoxy type contact cement.
i C. Substitutions: None accepted. D.
T
Finishes:
1. Chrome /Nickel Plating: Polished finish.
2.02 MATERIALS 1 2. Stainless Steel: No. 4 luster finish, unless specified otherwise.
3. Shop Primed Ferrous Metals: Pretreat and clean, spray apply one coat primer and bake.
A. 1/16 inch plastic laminate high pressure laminated to solid 45 lb density core. 2.03 FABRICATIONi1. Panels: 3/4 inch thickness.
2. Doors: 1 inch thickness.
3. Pilasters: 1 -1/4 inch thickness.
4 A. Weld and grind smooth joints of fabricated components.
4. Reinforcement for Anchorages: 12 gage. B Form exposed surfaces from one sheet of stock, free of joints. Form surfaces flat without distortion.
B . Pilaster Shoes: 3 inches high; Type 302/304, No. 4 stainless steel finish. Maintain flat surfaces without scratches or dents.
C. Attachments, Screws, and Bolts: Stainless steel; tamper proof type; heavy duty extruded aluminum
C. Provide steel anchor plates and anchor components for installation on building finishes. Hot -dip
galvanize ferrous metal anchors and fastening devices. brackets.
D. Back paint components where contact is made will i building finishes to prevent electrolysis.
E. Shop assemble components and package complete with anchors and fittings.
10165.1 10800 -1
WM - Lake Elsinore, CA July 16, 1993 I WM - Lake Elsinore, CA July 16,1993
F. Soap Dispensers: Wall mounted globe type for liquid soap; one per each lavatory. Mount at side
of faucet over lavatory.
1. Model No. 659, by Bradley.
2. Model No. 0350, by American Specialties.
3. Model No. B44, by Bobrick.
4. Model No. U118A, by A.J. Washroom.
5. Model No. 307 -6, by McKinney /Parker.
6. Model No. SD -3A, by Tubular Specialties.
G. Electric Hand Dryers: Model No. Al by World Dryer Corporation.
1. Color: Snow White PWHC.
2. Substitutions: None accepted.
END OF SECTION
10800.3
WM - Lake Elsinore, CA July 16, 1993
r..- . -.:.s .•. - -q ....- - '.... '/.'. - l,fs' ..
1.: { a- s•+ sriWf- ii..... aN M1R' . TW'. f?VS' .1'AIwY,+W%le.c.++.•WftTil,; n. C'w•NS"M"fNn {
i %RM y-y +K 3
k_,,
i4{4i{I iStid il l
THIS FILM WAS PHWVCED FROM, ! .
TOR BEST AND MOT COMPLRn ,I <
DRAWINGS AVAILABLE AT THE
1 Tag OF FILMI
w'
u