HomeMy WebLinkAbout31700 GRAPE ST_ 2077 (47)31700 GRAPE STREET 2077 16/30
VAL -MART
2.03 FINISHING
A. Aluminum Grille, Bottom Bar, and Guides: Mill finish aluminum.
B . Non- galvanized ferrous surfaces, except working parts of machinery: Factory coat of aluminum paint.
PART EXECUTION
3.01 INSTALLATION
A. Install to manufacturer's published instructions. Test for smooth operatio^ through full range of
motion; adjust as required.
B . Mount grilles to adjacent steel columns.
C. Use anchorage devices to securely fasten assembly to wall construction and building framing without
distortion or stress.
D. Fit and align assembly including hardware; level and plumb, to provide smooth operation.
E. Coordinate whn Section 08710 for cylinder installation.
END OF SECTION
WM - Lake Elsinore, CA
03332 -2
Juty 16, 1993
WM:
SECTION 08335
COILING COUNTER DOORS
052193
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Coiling counter doors.
B. Products Furnished by Others: Items noted'NIC' (Not in Contract), "coiling counter doors" at
Parmacy will be furnished by Wal -Mart, installed by Contractor.
1.02 REFERENCES
A. American Society for Testing and Materials (ASTM):
1. ASTM A526 - Steel Sheet, Zinc - coated (Galvanized) by the Hot -dip Process, Commercial
Quality.
2. ASTM A525 - General Requirements for Steel Sheet, Zinc - coated (Galvanized) by the Hot -Dip
Process.
B. National Fire Protection Association (NFPA)
1. NFPA 80 - Standard for Fire Doors and Windows.
C. UL - Underwriters Laboratories, Inc.
1.03 SUBMITTALS
A. Submit the following under provisions of Section 01300.
1. Product Data: Submit manufacturer's descriptive literature and'nstallation instructions.
2. Shop Drawings: Provide pertinent dimensioning, general consruction, component connections
and details. anchorage methods, hardware location.
1.04 QUALITY ASSURANCE
A. Qualifications: installation shall be by an authc.ized manufacturer's distributor in accordance with
NFPA 80 on approved mounting surfaces.
DART PRODUCTS
2.01 COILING COUNTER DOORS
A. Type: FD10 -1, Push-Up, bearing a Class B, 1 -1/2 hour, UL Label, by The Cookson Company,
SanFransico, CA. (415)626-0422
B. Substitutions: Under provisions of General Conditions and subject to compliance with requirements,
one of the following may be substituted for that specified. No other substltutir, a accepted.
1. Fire Shutter, by Atlas Roll-Lite Door Corporation. (201)572 -5700
2. Model RFS, by Ceco/Windsor Door. (312)789 -1400
3. Model LCN4, by Overhead Door Corporation. (214)233.6611
4. Rolling Counter Shutter, by Wayne -Dalton Corp. (218)674 -7015
5. Model No. PFL -IF Rolling Counter Fire Doors, by Cornell Iron Works. (800)233 -8366
6. Raynor Garage Doors, Dixon, IL. (815)288 -1431
2.02 COMPONENTS
A. Curtain: Interlocking flat slats of minimum 22 gage steel, ASTM A446, Grade A or ASTM A526;
galvanized with minimum 1.25 oz in accordance with ASTM A525; one piece for length of door.
B. Endlocks: To hold curtain in place and baffle air infiltration around curtain and glide.
C. Bottom Bar: Galvanized single angle.
08335 -1
WM - Lake Elsinore, CA July 16, 1993
ter,. w... _ .'g -^qtr •,»s+.- ,. ,
t ._. - .. .. ,., .. e.+....•,a+...- ....,c.. w.a. y.rmuw +c_.. ...y,_- ..a '':
f
aa.,.ic.._ . '..w.:x tr• ,,...r - ;.v.:. .+..,. :x,. .iota :NA :uw ':', -±w:a r. «_ °i :
ts'. .. . -.
a^ =^n"_: .r S .I.
THIS FILM CAR PRWUCM F8UN
ME BEST AND KNOT COMPIXTE
DRAWINGS All" ,.rACL9 AT THE
TIPS OF FF
r .
r,.
I
WM:
SECTION 08360
SECTIONAL OVERHEAD DOORS
01083
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Manual overhead sectional doors.
2. Operating hardware and supports.
3. Glass and glazing.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B. Product Compliance Letter: Submit on copy of form included in Section 01300.
1.03 SYSTEM DESCRIPTION
A. Performance Requirements: Wind load of 20 psf with deflection of no greater than 0.03 inches per
foot of opening width.
PART PRODUCTS
2.01 SECTIONAL OVERHEAD DOORS (INSULATED)
A. Model: Series 422, by Overhead Door Corporation.
B. Substitutions: Subject to compliance with requirements, one of the following may also be provided:
1. Model 732, by Atlas Roll -Llte Door Corporation.
2. Model 200RSI, by Ceco/Windsor Door.
3. Model 3300, by Clopay Corporation.
4. Model ST6201, by McKee Door, Inc., Aurora, IL, (800)222 -7426.
5. Model TC- 20(Tri- Core), by Raynor Garage Doors.
6. Model WMK520, by Wayne -Dalton Corp.
2.02 MATERIALS AND COMPONENTS
A. Steel Door Sections: 20 gage ASTM A446, Grade A or A526; galvanized; face pattern manufacturer's
standard.
B . Tracks, Supports, and Accessories: 3 inch track; galvanized; with ball bearing roller guides, door
stops, brackets, bracing, and reinforcing. Provide continuous neoprene or rubber weatherstripping
at top, bottom and jambs.
C. Counterbalance: Manufacturer's standard torsion spring mechanism for manual operation.
D. Hardware: Manufacturer's standard.
E. Perimeter Seal: Manufacturers standard.
F. Additional Components for Insulated Doors only:
1. Back Cover for Insulated Doors: 26 gage steel.
2. Insulation for Insulated Doors: Minimum (R.11.685). Provide one of the following insulation
materials.
1. Polyisocyanurate.
2. Polyurethane.
J. Polystyrene.
G. Vision Panel,, (Automotive Center "TBO ", and Garden Center): Manufacturers standard size,
double strength glass set into rubber or neoprene glazing channels for metal door sections.
08360 -1
WM - Lake Elsinore, CA July 16, 1993
0
2.03 ROOF HATCH LADDER
A. Steel Wall Ladder: As specified in Section 05500 - Metal Fabrications.
B. Ladder Safety Post: LadderUP, Model #1, by The Bilco Co., New Haven, Connecticut.
1. Telescoping tubular post, with stainless steel spring balancing mechanism and automatic locking
device for full extention. Unit to be complete, with fasteners for securing to ladder rungs.
2. Substitutions: None accepted.
PART EXECUTION
3.01 INSTALLATION
A. Install in accordance with manufacturer's instructions. Coordinate with installation of roofing system and
related flashings. Provide weathertight installation.
B . Apk' h,if --`nous pain. on metal surfaces of units In contact with cementitious materials and dissimilar
meti
C. Ladder Safety Post: Secure safety post to top two ladder rungs, on right side (climbing side), in
strict accordance with manufacturer's published instructions.
1. Adjust for smooth operation.
END OF SECTION
07722 -2
WM - Lake Elsinore, CA July 16, 1993
i
B. Silicone Sealant:
1. Silicone Sealant #1: ASTM C920, Type S, Grade NS, Class 25.
2. Silicone Sealant #2: ASTM C920, Type S, Grade NS, Class 25, mildew resistant.
a. Sanitary 1702 by General Electric Silicone Products Division.
b. 786 by Dow Corning Corporation.
2.02 ACCESSORIES
A. Primer: Non - staining type, recommended by sealant manufacturer to suit application.
B . Joint Cleaner: Non - corrosive and non - staining type, recommended by sealant manufacturer;
compatible with joint forming materials.
C. Joint Filler: Polyethylene foam rod, oversized 30% to 50 %.
D. Bond Breaker: Pressure sensitive tape recommended by sealant manufacturer to suit application.
PART 3 EXECUTION
3.01 EXAMINATION
A. Verify that surfaces and joint openings are ready to receive work and field measurements are as
shown on Drawings and recommended by the manufacturer.
B. Beginning of installation means installer accepts existing substrates.
3.02 PREPARATION
A. Clean and prime pints in accordance with manufacturer's instructions.
B . Remove loose materials and foreign matter which might Impair adhesion of sealant.
C. Verify that joint backing and release tapes are compatible with sealant.
D. Prutect elements surrounding work of this Section from damage or disfiguration.
3.03 INSTALLATION
A. Install sealant in accordance with manufacturer's instructions.
B. Measure joint dimensions and size materials to achieve required width/depth ratios.
C. Install joint backing to achieve neck dimension no greater than 1/3 the joint width.
D. Install bond breaker where joint backing is not used.
E. Apply sealant within recommended temperature ranges. Consult manufacturer when sealant cannot
be applied within recommended temperature ranges.
F. Install sealant free of air pockets, foreign embedded matter, ridges, and sags.
G . Tool joints concave.
3.04 SCHEDULE
A. General Exterior Construction and Expansion; Choice of:
1. Polyurethane Sealant #1, or
2. Silicone Sealant #1.
B. Horizontal Exterior Locations:
1. Polyurethane Sealant #2, or
2. Silicone Sealant #1.
I
WM - Lake Elsinore, CA
l
C. General Interior Construction:
1. Polyurethane Sealant #1, or
2. Silicone Sealant #1,
D. Interior Construction, Smooth Surfaces:
1. Silicone Sealant #2.
E. Horizontal Interior Locations:
1. Polyurethane Sealant #2.
END OF SECTION
07900 -2 '
079003
WM - Lake Elsinore, CA July 16, 1993
July 16, 1893
i
x Wt . ,.tr.y. .. . :.a 1 , - a, n.... .. ,u , .. fi. _ •]'c.... .. - -_ _ ..... .. ....... „`!....:.- - 1.. , ..,,... ,..... ... ,w, A.iai.,. yki !.i- ,......,u- 1laGival ,Aibt!FbiIAU.:}'}SD J "' ,'o:1vS5!
TI[IS FILM NAB PRODUCED FROM
THK BEST AND MOST COMPLETE j•,
DRAWINGS AVAILABLE AT "M
TIIR, OF FIL III4.
r..
0
D. Curtain Guides: Galvanized steel angles and channels. H. Exhaust Port (Automotive Center'TBO "): Manufacturer's standard, prime painted steel or aluminum
round port with cover.
E. Counterbalance: Manufacturer's standard adjustable helical spring mounted around steel shaft in
barrel. 2.03 FABRICATION
F. Automatic Closing Device: Thermally controlled by fusible link; may be manually operated for daily A. Fabricate door sections not more than 24 inches high, with horizontal meeting edges rolled to form
use. weather seal.
2.03 FINISHING B. Enclose ends and provide reinforcing required for stability.
A. Curtain Slats: Galvanized steel. G. Finish: Manufacturer's white baked primer coat.
B. Steel Guides and Hood Enclosure: Shop prime painted.
PART 3 EXECUTION
PART EXECUTION C'! EXAMINATION
3.01 EXAMINATION A. Verify, wall openings are ready to receive work and opening dimensions and tolerances are within
specified limits.
A. Verity that opening sizes, tolerances and conditions are acceptable for proper instal ation, including
heights and jamb widths. B . Beginning of installation means acceptance of existing surfaces.
3.02 INSTALLATION 3.02 INSTALLATION
A. Install fire rated coiling counter door unit assembly In accordance with manufacturer's published A. Install door unit assembly in accordance with manufacturers instructions.
instructions and NFPA 80. Test for smooth operation through full range of motion; adjust 2s required.
B . Anchor assembly to wall construction and building framing without distortion or stress.
B. Use anchorage devices to securely fasten assembly to wall construction and building framing without
distortion or stress. C. Securely brace door tracks suspended from structure. Socure tracks to structural members only.
C. Fit and align assembly including hardware; level and plumb, to provide smooth operation. D. Fit and align door assembly Including hardware, level and plumb, to provide smooth operation.
3.03 ADJUSTING F. Coordinate installation of sealants and backing materials at frame perimeter as specified in Section
07900.
A. Test for smooth operation through full range of motion; adjust as required.
G. Install perimeter trim and closures.
B. Test action with fusible link; restore to operating condition.
H. Install doors on vertical track or on high -lift track to maintain bottom of doors In open position at 12
inches top of CMU If track is bottomENDOFSECTIONaboveopening. c-irved required, curve at of joists.
3.03 ADJUSTING
A. Adjust door assembly to smooth operation.
3.04 CLEANING
A. Clean doors, frames and glass. Pemove labels and visible markings.
END OF SECTION
08335-2 06360.2
WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16,1993
SECTION 08381
WM: 05202
FLEXIBLE TRAFFIC DOORS
PART GENERAL
1.01 SUMMARY
I
i
A. Section Includes:
1. Double acting aluminum swinging traffic doors.
1.02 RELATED SECTIONS
A. Section 05500 - Metal Fabrications: Prepared opening with steel channel jambs and head.
1.03 SUBMITTALS
I
A. Submit the following under provisions of Section 01300.
1. Product Data: Include manufacturer's standard details for doors and frames, and installation
instruction for setting in steel or hollow metal frames.
2. Shop Drawings: Indicate application to project conditions.
rART2 PRODUCTS
2.01 FLEXIBLE TRAFFIC DOORSi
A. Easy Swing LWP3 Interior Double -Acting Door by Eliason Corporation, Kalamazoo, MI, (800)828 -
3655
B. Substitutions: Subject to compliance with requirements, one of the following may be substituted for
that specified.
1. Type 2 - Double Acting Door, by Carlson Products.
2. Series 2000 Rigid Traffic Doors, by Chase- Durus.
2.02 MATERIALS
A. Door: Standard lightweight aluminum door of 0.063 inch 6061 T6 aluminum alloy with satin anodized
finish both faces. Form edges for stiffness and easy swing gravity -type hingge with no springs.
1. Flexible Traff ic Doors at "Snack Bar" to receive plastic laminate finish, (Plastic Laminate B: No
D321 -6 Brittany Blue, by Wilsonart, or No. 85788 Federal Blue, by Formica), one side only.
Plastic laminate finish to be on side with view to the public.
B . View Window: 6x34 inch (200 sq in), clear acrylic safety window set in black rubber molding.
C. Hardware: As required for Installation conditions.
i
PART 3 EXECUTION
i3.01 EXAMINATION
A. Verify that openings are ready to receive work and opening dimensions and clearances are as
indicated on Drawings.
08381.1
WM - Lake Elsinore, CA July 16, 1993
I
vm Saw...x,..; ,...w,Yv xa..,r.: ,N. .e^..w a•.:.. dHU(': a:`,'x o. .:.•r:-at
rr.We9.ar- :yo-o,..t ._ . e..-- sece•.... r ........... ..c- .•..nw..+.;.
THIS FILM NLS P100DUCSD FIA N
i THE HEST AND MST COI<pLETS `
DRAWINGS AVAILABLE AT THE .
TI OF FIIAI
M
9
1
I
D. Astragals for Double Doors: Steel, specifically for double doors. For rated pairs of doors, provide SECTION 08331
SECTION 08111 astragal to meet UL rating requirements. If doors are provided that maintain rating without an WM: 03253
WM: 07272
STANDARD STEEL DOORS AND FRAMES astragal, submit door manufacturer's literature indicating UL rating. If U- shaped astragal is used that OVERHEAD COILING DOORS
does not require a coordinator, coordinate with Section 08710 to omit double door coordinator from
applicable hardware set.
PART 1 GENERAL
PART 1 GENERAL 2.05 PROTECTIVE COATINGS
1.01 SUMMARY
1.01 SUMMARY A. Bituminous Coating: Fibered asphalt emulsion, field applied.
A. Section Includes:
A. Section Includes: B. Primer: Exposed surfaces shall be cleaned, treated with Bonderite chemical and given one baked -on 1. Fire rated overhead coiling doors, operating hardware, manual operation.
1. Non -rated and rated rolled steel doors, panels, and frames. shop coat of grey synthetic primer. 2. Interior light frames. B. Related Sections:
2.06 FABRICATION 1. Section 05500 - Metal Fabrications: Miscellaneous concealed structural support for coiling doors.
B . Related Sections: 2. Section 08710 - Finish Hardware: Smoke seals and Cylinder core and keys.
1. Section 04100 - Mortar and Grout: Masonry mortar fill of metal frames. A. Fabricate units rigid, neat, and free from warp or buckle. Fabricate KD or welded as specified. Weld 3. Section 13810 - Energy Monitoring and Control Systems: Conduit from fire alarm control to
2. Section 08710 - Hardware: Door hardware coordination. exposed joints continuously; grind, dress, and make smooth, flush and invisible. electronic automatic closing device.
3. Section 08800 - Glazing: Glass in steel doors and frames. 4. Division 16 - Electrical Sections: Conduit from electric circuit to door operator and from door
4. Section 09900 - Painting: Field painting of doors and frames. B. Transom Bars for Glazed Lights: Fixed type, of same profiles as jamb and head. operator to control station.
1.02 REFERENCES C. Fabricate frames with hardware reinforcement plates welded in place. Provide mortar guard boxes. 1.02 REFERENCES
A. American National Standards Institute (ANSI): D. Fabricate frames in masonry wall coursing with 4 inch head member. A. American Society for Testing and Materials (ASTM):
1. ANSI At 17.1 - Specifications for Making Buildings and Facilities Accessible to and Usable by 1. ASTM A526 - Steel Sheet, Zinc- coated (Galvanized) by the Hot -dip Process, Commercial
Physically Handicapped People. E. Reinforce units to receive surface applied finish hardware. Quality.
2. ASTM 525 - General Requirements for Steel Sheet, Zinc - coated (Galvanized) by the Hot -Dip
I B . American Society for Testing and Materials (ASTM): 1y F. Silencers: Prepare frames for silencers. s
1. ASTM A525 - Steel Sheet, Zinc- Coated (Galvanized) by the Hot -Dip Process.
2. ASTM E152 - Methods of Fire Tests of Door Assemblies.
1. Single Doors: Provide three single rubber silencers on strike side.
2. Double Doors with Mullions: Provide three single rubber silencers for each door, on strike side. B. National Fire Protection Association (NFPA)
i
3. ASTM E413 - Classification for Determination of Sound Transmission Class. 3. Double Doors without Mullions: Provide two single silencers on frame head. 1. NFPA 80 - Standard for Fire Doors and Windows.
C. Door Hardware Institute (DHI):
1. DHI - The Installation of Commercial Steel Doors and Steel Frames, Insulated Steel Doors in G. Fire Rated Doors: Attach fire rated label to each door unit. 1.03 SUBMITTALS
Wood Frames and Builder's Hardware. H. Close top edge of exterior door flush with inverted steel channel closure. Seal joints watertight. A. Submit the following under provisions of Section 01300.
1. Product Data: Submit manufacturer's descriptive literature and installation instructions.
D. National Fire Protection Association (NFPA): I. Undercut non -rated doors as indicated on drawings. 2. Shop Drawings: Provide pertinent dimensioning, general construction, component connections
1. NFPA 80 - Fire Doors and Windows. and details, anchorage methods, hardware location.
2. NFPA 252 - Fire Tests for Door Assemblies.
PART 3 EXECUTION 1.04 QUALITY ASSURANCE
E. Steel Door Institute (SDI):
1. SDI -100 - Standard Steel Doors and Frames. 3.01 EXAMINATION A. Qualifications: Installation shall be by an authorized manufacturer's distributor in accordance with
2. SDI -105 - Recommended Erection Instructions for Steel Frames. NFPA 80 on approved mounting surfaces.
F. Underwriters Laboratories (UL):
A. Verify substrate conditions, opening sizes and tolerances are acceptable for proper installation.
B. Electrical Components: UL listed.
1. UL 10B - Fire Tests of Door Assemblies. 3.02 INSTALLATION
i
1.03 SUBMITTALS A. Install frames in accordance with SDI -105 and DHI. PART 2 PRODUCTS
A. Submit the following under provisions of Section 01300. B Install doors in accordance with SDI-11 00 and DHI. 2.01 COILING DOORS
1. Shop Drawings: Indicate frame configuration, anchor types and spacings, location of cutouts for
hardware, reinforcement, and finish. Indicate door elevations, internal reinforcement, closure C. Coordinate with adjacer„ wall construction for anchor placement. A. Type: FD -1 - Push -Up, Class "B" Fire Door, bearing a UL 1 -1/2 Hour label, by The Cookson
method, and cut outs for glazing. Company, SanFransico, CA. (415)826.4422
1.04 QUALITY ASSURANCE
D. Coordinate installation of glass and glazing.
B. Substitutions: Subject to compliance with requirements, coiling doors by one of the following
E. E Coordinate installation of doors with installation of hardware specified in Section 08710. manufacturers may be substituted for that specified.
A. Conform to requirements of ANSI /SDI -100 and ANSI At 17.1. 1. Atlas Roll -Lice Door Corporation, Edison, NJ. (201)572 -5700
1.05 REGULATORY REQUIREMENTS 3.03 ADJUSTING AND CLEANING 2. Ceco/Windsor Door, Oak Brook, IL. (312)789 -1400
3. Overhead Door Corporation, Dallas, T(. (214)233 -6611
A. Installed Door Assemblies: Conform to NFPA 80 for fire rated class as indicated.
A. Test for smooth operation through full range of swing; make necessary adjustments. 4. Raynor Garage Doors, Dixon, IL. (815)288 -1431
5. Model No. WMF089, by Wayne -Dalton Corp. (218)674.7015
B . Coordinate adjustment of doors with Installation of hardware. Adjust doors and hardware for smooth j 6. Model No. PFL Rolling Fire Doors, by Cornell Iron Works. (800)233 -8366
1.06 DELIVERY, STORAGE, AND PROTECTION and balanced door movement.
A. Protect doors and frames with resilient packaging. Break seal on -site to permit ventilation. END OF SECTION
2.02 COMPONENTS
I A. Curtain: Interlocking flat slats of minimum 22 gage steel, ASTM A446, Grade A or ASTM A526;
galvanized with minimum 1.25 oz in accordance with ASTM A525; one piece for length of door.
l
081113 08331 -1
08111 1
WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993
WM Lake Elsinore, CA Jury 16, 1993 y
r
a
y y.yrr l .: -.. .... - . , ."5rt. ..,. . ..: . .- ... g ,. . r. .r ., -. fm. . . l d.:!M1. y ! I :P . . . . . ...+. n ,r•a t. M '.. :y -w .. _ vr., .s . y. v.ru .vv... .N .r.. .,4 ...v . o. ,s >. n ... .,•i. . a. ..0 we«!s az.,fi+ ,xn,r waz ,- weu+s,as <w w.. . .. .,rn o. . ,a, .+,.r.... . ravrwr.w, .. .... .... ...., . . .r...• . :... . f ..,.;- .s . d ..i,_.. .. . .. ..... .. r.._.
1i :.
K1... ., f>: v} :!:IJfe.JL.tna3 t( idtY:aLnbuL O• J . LJ.Yi 4ti}rdklYw urclw A
1
saY . ..
uaa... ..: •.ae- .. .vi
9
THIS FILM WAS PBODUCBU FROK.' '
THE BEST AND MOST COMPLSTR
DRAWINGS AVAILABLB AT THE
TI OF FIS."I
W - ..
3.02 INSTALLATION SECTION 08410 B. Pivots:
WM: 070693 1. Center pivots for double acting doors.
A. Install door unit assembly to manufacturers installation instructions and final shop drawings. ALUMINUM ENTRANCES AND STOREFRONTS 2. Off -set pivots for single acting doors.
3. Intermediate Pivots: For doors, load bearing, to
B . Use anchorage devices to securely fasten door assembly to door frame construction without
single acting adjustable, surface applied: match
door finish. (Includes Door #1 01 C)
distortion or imposed stresses. PART 1 GENERAL
C. D t Locks: Mortise type, Adams Rite MS- 1850A, less cylinder. See Section 08710 for
C. Ensure that plastic laminate side of door faces public space. 1.01 SUMMARY cylinders.
3.03 CLEANING A. Section Includes: D. PushlPulls: Type CP -2 push and type CO-9 pull, by Kawneer Company, Inc. Color: #14 Clear
1. Aluminum doors, frames and glazed lights. Anodized.
A. Remove protective materia from pre - finished surfaces. 2. Vision glass and infill panels. 1. Single Acting Doors: Push/Pulls.
3. Anchors, brackets, and attachments. 2. Double Acting Doors: Push only, for both sides of doors.
B. Remove labels and visible markings. 3. Door hardware.
E. Flush Bolts /Interlocking Device: Provide interlocking device for pairs of doors, acceptable to
C. Wash down surfaces with a solution of mild detergent in warm water, applied with soil, clean wiping B. Related Sections: authorities having jurisdiction. Provide one of the following.
cloths. Wipe surfaces clean. 1. Section 04220 - Concrete Unit Masonry: Preparation of adjacent work to receive work of this 1. Controller Locking System, by Kawneer. (Prefered system.)
section. 2. No. 4015/4085, 3 point lock, by Adams Rite.
END OF SECTION 2. Section 07900 - Joint Sealers: Perimeter sealant. 3. Substitutions: None accepted.
3. Section 08460 - Automatic Doors: Coordination between components.
4. Section 08710 - Finish Hardware: Coordinate cylinders, threshoids and other hardware. F. Door Holder (Exte %r doors only): 1221 -4 cast iron, finish to match door color, by Trimco - Triangle
5. Section 08800 - Glazing: Glass products. Brass Mfg. Co.
1.02 REFERENCES G. Retractable Door Stop (double acting doors only)): Breakaway type, Model 1150A, by Dor- o- matic,
or similar as furnished by named manufacturers, for "double acting" doors only. Break -away must be
A. Americans with Disabilities Act of 1990: Accessibility Guidelines for Buildings and Facilities. code approved and acceptable to local authorities having jurisdiction.
B. American National Standards Institute (ANSI): H. Weatherstripping, for Exterior Doors only:
1. ANSI At 17.1 - Specifications for Making Buildings and Facilities Accessible to and Usable by 1. Head and Jamb: Replaceable wool, polypropylene, or nylon wool pile with aluminum strip
Physically Handicapper) People. backing, recessed in frame; AAMA 701.2.
2. Sill: Semi -rigid polymeric material on aluminum anodized to match door; EPDM sweep strip;
C. American Society for Testing and Materials (ASTM):
Air Exterior Windows,
38 -560 by Kawneer or similar by other named manufacturers
1. ASTM E283 - Rate of Leakage through Curtain Walls and Doors.
2. ASTM E330 - Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform I. Threshold: See Section 08710.
Static Air Pressure Difference.
J. Bumper Guards: Nominal 1/2 x 2 inch aluminum bars, one centered 6 inches AFF, the other centered
D. Federal Specification (FS): 24 inches AFF, flush mounted stile -to- stile. Coordinate with Section 08460.
1. FS TT -P -31 - Paint, Oil: Iron Oxide, Ready Mixed, Red and Brown. 1. Install bumper guards both faces of Interior and exterior Vestibule doors.
2. FS TT -P -641 - Primer Coating: Zinc Dust -Zinc Oxide (for Galvanized Surfaces). 2. Install bumper guards both faces of Garden Center doors.
1.03 SYSTEMS DESCRIPTION K. Finger Protector (Double Swing Doors): No. 38 -365, by Kawneer.
A. Performance Requirements: L. Exit Devices (Doors at Vestibule): Concealed Rod, by Dor- O -Matic 990.
1. Air Infiltration: ASTM E283, infiltration not to exceed 0.06 CFM per sq. ft. of fixed area.
2. Water Infiltration: ASTM E331, no water penetration at a test pressure of 8.0 PSF. M. Exit Devices (Door at Vision Center): Model No. 1090 Rim Type Crash Bar -Panic Device, with
finish, 3. Structural Performance: Maximum deflection of 1/175 of span. Allowable stress with 1.65 safety adjustable roller strike, by Dor- O- Matic. Pull: Style CO-9 pull handle, with 014 clear anodize
factor. System shall perform to these criteria under a windload of 20 PSF, by Kawneer Company, Inc.
1.04 SUBMITTALS N. Exit Devices (Gardr,i Center): "Panic Guard" system with Style CO -9 pull handle, with #14 clear
anodize finish, by Kawneer Company, Inc. Use on Garden Center Doors only.
A Section 01300 - Submittals: Procedures for submittals.
2.05 FABRICATION
B . Letter of Conformance: Submit on copy of Letter of Conformance form at end of this Section.
A. Fabricate doors and frames allowing for rdnimurn cleararn -es and shim spacing around perimet,
1.05 QUALITY ASSURANCE assembly, yet enabling installation.
A. Conform to requirements of ADA and ANSI At 17.1. B . Rigidly fit and secure joints and comers. Make joints and connections flush, hairline, and
weatherproof.
PART 2 PRODUCTS C. Develop drainage holes with moisture pattern to exterior.
2.01 MANUFACTURERS D. Prepare components to receive anchor devices. Fabricate anchorage items. Arrange fasteners,
attachments, and jointing to ensure concealment from view.
A. Kawneer Company, Inc. (Manufacturers contact: Mr. Rodney Frey, (317)738 -2600, (317)738. 2170.)
FAX: (800)755. 4639). E. Prepare components with internal reinforcement for door hardware.
08381- 2 08410.1 08410.3
WM Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16, 1993
Y
c .. - .. rr1.e ,a..,- wu. >.... - ...s,.. u . ;. -,.. .:. ,. .. ... _. ,. .. .....
y. >
a,...
4,., .. „
e ,
y, -.- ., .5........
a- ....:.e ... , n ... .. tt... u.'ti. .x. r stiv < .1.H.v . . W +1 .ham .. vt . > r -0H+ +ek•' ct _ a.. n_ t ._ _ ./ « a« .. .- . -. _.a ,. ,. / . h/ 4' Lu. 4_.- 41ie,}'1L4hi,.lJtI WS'J wS ie+.Va/G W' ewa.w.. -
w , .
1 L vMi iMae.' ."welmva Wirr.,lr s _.www...w... .`..hr _ ._...., ..w r -.£ ..t -f
Y
4F9 - yr.... • , s.r y.. . _1%
THIS FILM WAS PRODUCED FROM
THE BEST AND MOST COMPLETE
DRAWINGS AVAILABLE AT THE
TIME OF FILM ..`-
o
d
1.07 PROJECT /SITE CON7)ITIONS
B . Endlocks: To hold curtain in place and baffle air infiltration around curtain and glide.
A. Field Measurements: Verify that field measurements are as indicated on shop drawings.
C. Bottom Bar: Galvanized single angle.
B. Coordination: Cooru :. '9 the work with door opening construction, door frame and door hardware
installation. D. Curtain Guides: Galvanized steel angles and channels. 1/8 inch thick steel, minimum.
E. Counterbalance: Manufacturer's standard adjustable helical spring mounted around steel shaft in
PART 2 PRODUCTS barrel.
2.01 MANUFACTURERS F. Electronic Automatic Closing Device: Firefly Time -Delay Release Device, 24 volt D.C., by The
Cookson Company. Provide unit complete, including fusable link, test buttons and status indicator
A. Subject to compliance with requirements, provide doors, panels and frames of one of the following: lights.
1. Amweld Building Products Division. 1. Substitutions: Subject to compliance with requirements, one of the following may be
2. Ceco Door Division. substituted for that specified.
3. Copeo Door Co. a. Firescout, by Atlas Roll -lite Door Corporation.
4. Curries. b. Automatic Closing Device, by Rixon.
5. Fenestra Corporation.
6. Kewanee Corporation. 2.03 FINISHING
7. Mesker.
8. Republic Builders Products. A. Curtain Slats: Galvanized steel.
9. Steelcraft Manufacturing Co.
B. Steel Guides and Hood Enclosure: Shop prime painted.
B. Substitutions: None accepted.
2.02 DOORS AND FRAMES PART 3 EXECUTION
A. Interior Doors: SDI -100, Grade I, Standard -Duty, Model 3, Seamless - Hollow Steel Construction, 3.01 EXAMINATION
20 gage cold - rolled steel.
A. Verify that opening sizes, tolerances and conditions are acceptable for proper Installation, Including
B . Exterior Doors: SDI -100; Grade III, Extra Heavy Duty, Model 3, Seamless - Ho'ow Steel heights and jamb widths.
Construction, 16 gage galvanized (ASTM A525) steel. Fabricate head with inverted, unperforated
channel flush with top edge to exclude water. 3.02 INSTALLATION
C. Interior Frames: 16 gage, cold- rolled steel, mitered and welded or KID units. A. Install door unit assembly in accordance with manufacturer's published instructions and NFPA 80. Test
1. Jamb depth: Sized to ill wall thickness. for smooth operation through full range of motion; adjust as required.
D. Exterior Frames: 16 gage, galvanized (ASTM A525) steel, mitered and welded units. B. Use anchorage devices to securely fasten assembly to wall construction and building framing without
1. Jamb depth: 5 -3/4 ", unless shown otherwise. distortion or stress.
E. Mullions for Double Doors: Type, specified in Section 08710 or as detailed on drawings. C. Securely brace components suspended from structure. Secure guides to structural members only.
2.03 CORE CONSTRUCTION D. Fit and align assembly including hardware; level and plumb, to provide smooth operation.
A. Provide one of the following core construction; Contractor's option: E. Coordinate installation of electrical wiring from Owner's fire alarm system to door closing device.
1. 22 gage vertical steel stiffeners space 6 Inches apart and spot welded to face sheets at 6 inches
on center. Insulate spaces between stiffeners with loose fill insulation full height of door. 3.03 ADJUSTING
2. Polyurethane core foamed in place or laminated, 20 psi strength, 1.8 pct density; 112 Inch
maximum voids in any direction. (R.12) Strength of bond between core and steel face sheet A. Test for smooth operation through full range of motion; adjust as required.
shall exceed strength of core so delamination will not occur during operating conditions.
3. Rigid core of polystyrene foam board, 1500 psf compressive strength, 18 psi shear strength. B . Test action with automatic closing device; restore to operating condition.
R.7) Strength of bond between core and steel face sheet shall exceed strength of core so
that delamination will not occur under operating conditions. END OF SECTION
4. Honeycomb Core: Not acceptable.
2.04 ACCESSORIES
A. Rubber Silencers: Resilient rubber.
B. Glazing Stops: Rolled steel channel shape, butted comers; prepared for countersink style screws.
C. Plaster Guards: Provide 26 gage steel plaster guards or mortar boxes, welded to frame, at back of
hardware cutouts in masonry openings.
I
08111 -2 08331 -2
WM - Lake Elsinore, CA July 16, 1993 WM - Lake Elsinore, CA July 16,1993
t -. .- +
a ::
i..,.e .xt as ....•.w „q <i. .. .. a ... - _ i <,... >>;.`- ...t<c ,. n _, rk.+fi•r%Kaa:i As>s•v u:«gsvrsx:rtwY•..•x w» y q ,r. ..c.i ... ,,. s:.. e.. -... ,.._, ..... r ,.. .:.. .w <,. y,P. rx.,..... .w .. vn." /V..:.r ,SO.,M 4.iC. 35. tx !C ,.. .:s... i . .Iwo RM .!e!!. 14Y r... e. .. .- "%•V .. r. x. Mw l....oi rw v: ._ , .
or- 1W1''.LS..- ..ve,.aurwwo.!.t
THIS FILM WAS PBODDCED FKM
THE BEST AND Ii 0011PLETE
DRAWINGS AVAILABLE AT THE
T.OF^ FIL11I
l
F
e WM:
SECTION 08332
OVERHEAD COILING GRILLES
12072
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Standard overhead coiling grilles; manual operated.
B. Related Sections:
1. Section 05500 - Metal Fabrications: Miscellaneous concealed structural support for grilles.
2. Section 08710 - Hardware: Cylinders and threshold for use with Grilles.
1.02 REFERENCES
A. American Society for Testing and Materials (ASTM):
1. ASTM A446 - Steel Sheet, Zinc Coated (Galvanized) by the Hot -Dip Process, Structural
Physical) Quality.
2. ASTM A525 - General Requirements for Steel Sheet, Zinc - coated (Galvanized) by the Hot -Dip
Process.
3. ASTM A526 - Steel Sheet, Zinc - coated (Galvanized) by the Hot -Dip Process, Commercial
Quality.
1.03 SUBMITTALS
A. Submit the following under provisions of Section 01300.
1. Product Data: Submit manufacturer's descriptive literature and installation instructions.
2. Shop Drawings: Provide pertinent dimensioning, general construction, component connections
and details, anchorage methods, hardware location.
PART PRODUCTS
2.01 COILING GRILLES
A. Type: Model No. GB -4, by The Overhead Door Corporation, Dallas, TX. (214)233 -6611
B . Substitutions: Subject to compliance with requirements, one of the following may be substituted for
that specified.
1. American Rolling Door Co.
2. The Cookson Company. (415)826.4422
3. Atlas Roll -Lice Door Corporation, Edison, NJ. (201)572 -5700
4. Ceco/Windsor Door, Oak Brook, IL. (312)789 -1406
5. Raynor Garage Doors, Dixon, IL. (815)288 -1431
6. Wayne -Dalton Corp. (218 674.7015
7. Cornell Iron Works. (800)33 -8366
2.02 COMPONENTS
A. Curtain: 5/16 inch diameter alumi, rum rods, spaced 2 Inches max. on center with interlocking links
spaced 9 inches max. on center.
B . Endlocks: Secured to curtain rods to prevent lateral movement and act as wearing surfaces.
C. Bottom Bar: Extruded aluminum box type, for use with cylinder lock. Cylinder lock to be operable
from both sides.
D. Curtain Guides: 6063T6 extruded aluminum with curtain - retaining grooves aligned with continuous
silicon- treated wool pile strips.
E. Counterbalance: Manufacturer's standard adjustable helical torsion spring, mounted around steel
shaft in barrel, with grease - sealed ball bearings or self- lubricating graphite bearings for rotating
members.
08332 -1
WM - Lake Elsinore, CA July 16, 1993
110 1
II
1. 2
T.
13
0
z