HomeMy WebLinkAbout31700 GRAPE ST_ 2077 (21)PART PRODUCTS
2.01 MANUFACTURERS
A. Subject to compliance with requirements, provide spacial flooring system of one of the following
manufacturers:
1. LockShield System, by Ameron Protective Coatings Division, Brea, CA. (800)344 -0025
2. Nitoflor System, by Fosrock, Plainview, NY. (800) 645 -3954.
B. Substitutions: None accepted.
2.02 LOCKSHIELD SYSTEM
A. Curing Compound (optional): Nu -Klad 105A epoxy primer and sealer, by Ameron.
B. Epoxy Coating: Amerlock 400 a coy, by Ameron.
1. Color: OSHA Safety Red, RD -2 rod.
2. Color: OSHA Safety Yello r..
C. Polyurethane Coating: Amershleld Aliphatic Polyurethane, by Ameron.
1. Color: OSHA Safety Reu, RD -2 red.
2. Color: OSHA Safety Yellow.
D. Non -Skid Additive: Amercoat #886, by Ameron. Pumice additive, 2 pints per gallon of polyurethane
coating.
2.03 NITOFLOR SYSTEM
A. Primer: Niloflor FC 140, thinned 50% by volume with Solvent 102. by Fosroc.
A. Primer (California): Nkoflor FC 130E Epoxy Primer (water base), by Fosroc.
B. Epoxy Coating Nttoflor FC 140, full strength, by Fosroc.
1. (;olor: "Wal -Mart Red ".
2. Color: "Wal -Mart OSHA Safety Yellow".
B. Epoxy Coating (California): Nitof or FC 130E Color Coat (water base), by Fosroc. (Full strength
application.)
1. Color: "Wal -Mart Red ".
2. Color: "Wal -Mart OSHA Safety Yellow".
C. Polyurethane Coating: Nitoflor UR512 Urethane, by Fosroc.
1. Color: "Wal -Mart ReJ ".
2. Color: "Wal -Mart OSHA Safety Yellow ".
D. Non -Skid Additive: Pumice additive, 2 pints per gallon of polyurethane coating, as recommended by
Fosroc.
PART EXECUTION
3.01 ACCEPTABLE INSTALLERS
A. Approved Ameron Applicators:
1p
proved
Corporation, 3200 S. 6th Street, Lincoln, NE 68502, (402)423.2545. Lynn Parpart, or
Ben Parparl.
2. Pro -Tech Coatings, Inc., 1920 Stedman, St. Louis, MO 63114, (314)427 -8644. Mark Selbel.
3. CCS Flooring, Inc., 524 Morse Avenue, Schaumberg, IL 60193, (708)893 -0901. Gram Johnson,
Jr.
4. Grave Johnson Co., 2218 University Ave., S.E., Minneapolis, MN (612)379 -2825, (612)379 -0907
FAX, Gary Trimm.
5. Advanced Coatings Designs, 2605 Temple Heights, Suite F, Oceanside, CA 92056, (619)631-
5070 (619)630 -7636 fax, Stacey Ingram.
6. Beugler Industrial Flooring, P.O. Box 6232, Concord, CA 94524, (510)439 -0197
7. •Howard & Wills Contracting, Inc., 317 Salem Drive, Owensboro, KY 42301, (502)685 -3023.
502)684 -3688. Steve Wills
09700 -2
WM - Lake Elsinore, CA July 16,1993
I
t 8.
l
Apply, trowel, and float filler to achieve smooth, flat, bard surface. Use only fillers which are
to Grind Irregularities
WM;
SECTION 09780
05202
acceptable coating manufacturer. above the surface level. Prohibit traffic until ifillerPscured.
FLOOR TREATMENT
C. Vacuum clean substrate. PART 1 GENERAL
D. Water -cured concrete must be cured a minimum of 14 days and have attained 80 percent of its final 1.01 SUMMARY
strength. Prepare surface in accordance with ASTM D4259 or ASTM D4260 with muriatlo acid using
equal parts of acid to water by volume. A. Section Includes:
1. Concrete surfaces cured with conventional curing compounds or contaminated with fomn oils must ; 1. Application of stripper, sealer, and finish to tile specified in Section 09650.
be completely c.3aned by ASTM D4259. Clean concrete surfaces by abrasive blasting per
ASTM 4269. Acid etching is not acceptable, as it will rat sufficiently remove these contaminants. 1.02 QUALITY ASSURANCE
E. Concrete Curing: New concrete which has been cured with the approved curing compound specified ( A. Stripper Crew Requirement: Four -man crew; one to apply solution ahead of buffer, one to run
herein, will not require blasting or etching Remove fins and projections from concrete surfaces, and
ensure that surfaces free from oil and other
slow -speed buffer, two with mops and buckets to pick up dirty solution behind buffer and rinse floor
are contaminants. prior to applying sealer and finish.
1. Apply to slabs immediately after final finishing operation or upon disappearance of the "bleed -
water sheen" of surface moisture.
2. Prior to application of subsequent coats of epoxy, water and detergent wash for dirt, oil and PART 2 PRODUCTS
grease removal.
2.01 MATERIALS
i 3.04 PRIMER APPLICATION
A. Stripper. Bravo Stripper, by Johnson Wax.
A. Primer coat is required for Niloflor System only.
B. Sealer: Over and Under Resilient Tile Sealer, by Johnson Wax.
B. Prime property prepared concrete surface with NiMlor primer in strict accordance with manufacturers
r Instructions. Allow to cure for 24 hours before proceeding. C. Finish: Sprint Floor Finish, by Johnson Wax.
3.05 EPDXY COATING APPLICATION D. Substitutions: None accepted.
A. Prepare epoxy components in accordance with manufacturers instructions. Use manufacturers f
specified mix rig ratios. Thoroughly mix blended to
2.02 EQUIPMENT
resins and cure components until uniformly a
workable consistency. Do rat mix more material than can be used within the expected pot life. Do A. Use the following equipment to perform work of this Section:
not apply material when time has gone past the recommended pot life. )
1. Dry film thickness: 5
1. One automatic floor scrubber (with full charge.)
mils. ! 2. Two or three side -to -side slow speed buffers.
3. Five black stripping pads.
B . If thinning is necessary, add thinners in strict accordance with coating manufacturers instructions. 4. Five buckets with wringers.
5. Six mop head and handles. Soak new maps for 24 hours.
i
C. Maintain optimum application temperature range. Pt aPP n9 6. Two clean dust mops.
D. Apply epoxy coating in wet even coats, with 50 percent overlap to avoid holidays, bare areas and
urrt is completely and uniformly coated without thick or ponded areas PART 3 EXECUTIONwhichwilladversely
affthe
3.01 PREPARATION
E. Ventilate comined areas with clean air between coats and while curing the final coat. Maintain surface
temperature at least 5 degrees F above dew point to prevent moisture condensation betweun i j A. Stripping should not commence for a week or more after Installation of tile to ensure that tiles are
teat laying flat and are fully adhered to the substrate.
F. Repair damaged areas by brush or spray. 3.02 STRIPPING
3.06 POLYURETHANE COATING APPLICATION j A. Dust mop entire sales floor and repave gum, tar, glue, ate. from floor.
A. Prepare urethane components in accordance with manufacturers instructions. Use manufacturers B. Mix one part Stripper to four parts hot water.
specified mixing ratios. Thoroughly mix resins and cure components until uniformly blended to a
workable consistency. Do rat mix more material than can be used within the expected pot life. Do
not apply material when time has the recommended life.
C. Dip mop in stripping solution, let excess solution drain off, and apply stripper to floor. Let stripper
Do to dry floor. gone past pot
1. Dry film thickness: 5 mils.
set on floor five minutes before scrubbing. not allow stripper on
ii B Thin for M is in
D. Important: With black stripping pad under the slow speed buffor, pass over each tile section at least
itonlyasrequiredworkability. thinning necessary, add thinners strict accordance with twice. Do not rush this procedure; is crucial.
coating manufacturers Instructions.
E. After a section is stripped, pick up tho stripping solution immediately with we• vacuum. A
C. Maintain optimum application temperature range, in order to prevent condensation.
i 1 F. Rinse thoroughly by mapping with clear water, removing remaining solution, finish, and dirt. Use wetD. pp y g ap rig p percent. } Apply urethane coating in wet even coats, over) i each ass 50 vacuum for water pickup.
097801
09700-4 )
WM - Lake Elsinore, CA July 16,1993
WM - Lake Elsinore, CA July 16,1993 (
u " ++.r+ae,r.•r• ,,,
H,,i .,. ,. y . n.wyi'zC".'R:.XI 4R4rLl2e4: Tis`! .'' LS» E' .''. Y7 fMY79FlfiAT1'ri'ti+a 4n'+cxP s. Srh?t; -w'^. •tk'-H°?4c .i7 i0'tMX KMMiai.' f .[+Ff4dk•.WH4s ^`h!':rtR'ltl Y'' -.. °.`:PfA,,, S.S'7:v ... `. A'. .W "iN?P'.4: R• ?LRW'blflid'A 6/B!R 94Ml Mfi^X. 4R7 R +'7 7kQn`ri(-{Y7 C9`GWR^'. ;J!s?V
7. .. . ..4,.fTi''.,'- ",r"h'• _ _ 4xAa.%f.'Y .l l:.l..nd: d;'
47E 191 W a>l ll COMM
IN08 AVAILAWA
07 II
4
B . Label each container with color, type, texture, room locations, in addition to the manufacturer -, label.
PART PRODUCTS
2.01 MANUFACTURERS
A. Paint: Pittsburgh Paints, by PPG Industries, Inc.
B. Substitutions: Subject to compliance with requirements, one of the following manufacturers may be
substituted for that specified.
1. Devoe & Reynolds Co., Inc.
2. Diamonds Jogel Paints.
3. Dunn Edwards.
4. Frazee.
5. Fuller O'Brian.
6. Glidden Coatings and Resins.
7. Kelly Moore Paints.
8. MAB Paints and Coatings.
9. Pratt & Lambert. Inc.
10. Rodda.
11. Sherwin- Williams Company.
2.02 MATERIALS
A. Paint Accessory Materials: Linseed oil, shellac, turpentine and other materials not specifically
indicated herein but required to achieve the finishes specified of high quality and approved
manufacturer.
B. Paints: Ready- mixed; pigments fully ground maintaining a soft paste consistency, capable of readily
and uniformly dispersing to a complete homogeneous mixture.
C. Paints to have good flowing and brushing properties acid be capable of drying or curing free of
streaks or sags.
PART EXECUTION
3.01 EXAMINATION
A. Applicator shall examine areas aru conditions under which painting work is to be applied and notify
contractor in writing of conditions uatrimental to proper and timely completion of work. Do not
proceed with work until unsatisfactory conditions have been corrected.
3.02 PREPARATION
A. Clean and prepare surfaces for painting to manufacturers instructions for substrate to be painted.
3.03 APPLICATIONS
A. Apply each coat at proper consistency.
B. Each coat of paint is to be slightly darker than preceding coat unless otherwise approved by
Wal -Mart Construction Manager. Sand lightly between coats ff necessary to achieve required finish.
C. Do not apply finishes rin surfaces that are not sufficientty dry.
D. The number of coats and film thickness required is the same regardless of the application method.
Do not apply succeeding coats until the previous coat has cured as recommended by the
manufacturer.
E. Apply additional coats when undercoats, stains, or other crndtio ,s show through final coat of paint
until paint film is of uniform finish, colar, anrf apn,aarance. Give spacial attention to ensure that
surfaces, including edges. corners, cr *vices, we cis, znd exposed fasteners, receive a dry film
thickness equivalent to that of flat surfaces.
09900 -2
WM - Lake Elsinore, CA July 16, 1993
M
F. Minimum Coating Thickness: Apply materials at not less than the manufacturer's recommended
spreading rate. Provide a total dry film thickness of the entire system as recommended by the
manufacturer.
G. Block Fillers: Apply block fillers to concrete masonry units at a ra!e to ensure complete coverage wi!h
pores filled.
H. Prime Coats: Before application of finish coats, apply a prime coat of material as recommended by
the manufacturer to material that is required to be painted or finished and has not been prime coated
by others. Recoat primed and sealed surfaces where evidence of suction spots or unsealed areas in
first coat appears, to assure a linish coat with no burn through or other defects due to insufficient
sealing.
1. Pigmented (Opaque) Finishes: Completely cover to provide an opaque, smooth surface of uniform
finish, color, appearance, and coverage. Cloudiness, spotting, laps, brush marks, runs, sags, or
other surface imperfections will no! be acceptable.
I. Transparent (Clear) Finishes: Use multiple coats to produce a glass - smooth surface film of even
luster. Provide a finish free of laps, cloudiness, color irregularity, brush marks, runs, sags, orange
peel, nail holes or other surface imperfections.
J. Compler.:d Work: Match approved samples for color, texture, and coverage. Remove, refinish, or
repaint work not in compliance with specified requirements.
3.04 MECHANICAL AND ELECTRICAL EQUIPMENT
A. Replace identification markings on mechanical or electrical equipment when painted over or spattered.
B. Paint exposed conduit and electrical equipment occurring in finished areas where it will be exposed
to the public. Color and texture to match adjacent surfaces.
C. Paint both sides and edges of plywood backboards for electrical equipment before ir.stalling
backboards and mounting equipment on them.
D. Prepaint Gas piping prior to installation.
3.05 CLEANING
A. As work proceeds and upon completion, promptly remove paint where spilled, splashed, or
shattered. During progress of work keep premises free from any unnecessary accumulation of tools,
equipment, surplus materials, and debris.
B. Upon completion of work leave premises neat and clean.
3.06 PROTECTION
A. Protect other surfaces from paint and damage. Repair damage as a result of inadequate or
unsuitable prota lion.
3.07 PAINTING AND FINISHING SCHEDULE (EXTERIOR)
Paint Schedule provides for minimum two -coat application. Third coat may be required by ' "al -Mart
Construction Manager to give complete coverage and uniform appearance. Omit prime jr items
shop primed.
Unless otherwise indicated, pain: systems scheduled below are by PPG. Systems of similar
performance by other specified manufacturers are acceptable.
A. Ferrous Meia!: Solvent Base, Gloss, Modified Alkvd Resin. (Including Prepainted Gas Piping,
Sectional Overhead Doors and Hollow Metal Door and Frames)
1st Coat: PPG Speedhide Rust Inhibitive Stee! (Red or Grey), 6 -208 series.
2nd Coat: PPG Speedhide Alkyd Gloss Enamel, 6 -252 series.
WM - Lake Elsinore, CA
THIS FILM WAS PRODUCED FROM
THE BEST AND MOST COMPLETE
DRAWINGS AVAII.ABLE AT THE
TIIIIE OF FI^ LMING
r
F,
July 16, 1993
J
w
SECTIOI
WM: 07132
i
WALLCOVL. oS
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Prepare surfaces to receive wallcoverings.
2. Adhesive -apply wallcoverings.
j 1.02 REFERENCES
A. Federal Specification (FS):
1. FS Or W 408 - Wallcovering -Vinyl Coated.
2. FS L -P 1040 - Plastic Sheets and Strips, Polyvinyl Fluoride (Top Coat).
B. American Society for Testing and Materials (ASTM):
1. ASTM F 793 - Classification of Wallcovering by Durability Characteristics.
1.03 SUBMITTALS
A. Submit the following under provisions of Section 01300.
1. Area calculations for wallcovering quartity requirements including calculated waste.
2. Submit manufacturers literature for recommended adhesives.
3. Flame Spread rating.
1.04 QUALITY ASSURANCE
A. Certification: Wallcovering and adhesive shall have been tested to provide a U.L. Class "B" fi e
hazard classification.
1.05 DELIVERY, STORAGE, AND HANDLING
A. Receive, handle, and store materials to prevent damage. After receipt, inspect all wallcovering to
determine condition.
1. After receipt of wallcovering materials, the contractor shall be responsible for replacing all
damaged materials.
iB . Store 2!I wallcovering in undamaged condition as packaged by the manufacturer, with manufacturers
seals and labels in ''act.
i 1. Store all materials flat in a clean dry area with maintained temperature above 40 degrees F.
C. Exercise care to prevent damage during handling and storage.
D. Take precautionary measure to prevent fire hazards with adhesives and solvents.
1.06 SITE CONDITIONS
A. Maintain areas to receive wallcovering at a constant minimum temperature of 45 -50 degrees F. for at
least three days before, and all during, the application period.
1. Make sure maximum surface moisture conforms to wallcovering manufacturers requirements and
i
surface exhibits negative alkalinity.
B. Provide adequate and continuous ventilation during work and after installation of wallcovering.
j PART PRODUCTS
2.01 MATERIALS
A. Wallcovering material will be furnished by Wal -mart for installation by contractor.
1. Wallcovering:
a. Manufacturer: Sellers & Josephson "Skye" #899 -8123.
09950 -1
WM - Lake Elsinore, CA July 16, 1993
J
w
G. Move stripping operation to next area of sales floor and repeat the procedure.
H. Let floor dry completely.
3.03 SEALING
A. Apply 2 coats of specified sealer in strict accordance with manufacturers Instructions.
3.04 FINISHING
A. Pour specified floor finish Into clean mop buckets.
B. Prepare new or clean mop for applying floor finish.
C. Dip mop in floor finish, place mop in wringer and tap lightly. The mop should be full but not
dripping.
D. Apply two coats of specified finish to floor. Under normal conditions, allow a minimum of 45 minutes
drying time between coats.
E. Important: Air conditioning or heat must be in operation to assure adequate drying time and curing of
finish between coats.
END OF SECTION
09780.2
WM - Lake Elsinore, CA July 16,1993
SECTION 09800
WM: 04093
SPECIAL COATINGS
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Masonry Weatherproofing System: Cementitious and Acrylic waterproofing coatings and
decorative acrylic finish coat systems.
B. Related Sections:
1. Section 04220 - Concrete Unit Masonry: Exterior masonry walls to receive weatherproofing
system as indicated on drawings.
2. Section 09900 - Painting: First coat to include area of blue and red accent bands.
1.02 REFERENCES
A. American Society for Testing and Materials (ASTM):
1. ASTM D968 - Abrasion Resistance of Organic Coatings by the Falling Abrasive Tester.
2. ASTM D822 - Operating Light and Water Exposure Apparatus (Carbon Are Type) for Testing
Paint, Varnish, Lacquer, and Related Products.
3. ASTM G26 - Operating Light - Exposure Apparatus (Carbon Arc Type) With and Without Water
for Exposure Nonmetal Materials.
B. State of Alabama Highway Department Specifications for Freeze -Thew Tests on Concrete Coating
Material for Bridge Finishes.
1.03 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B . Product Date, Submit in letter form, the manufacturer and colors selected.
1.04 QUALITY ASSURANCE
A. Applicator Qualifications: Properly trained and approved by the weatherproofing system
manufacturer and have authorization to offer specified warranty. Submit installer letter of certification,
signed by Technical Representative of system manufacturer.
B. Field Sample:
1. Apply masonry weatherproofing system to sample precast concrete panel.
2. Reflect proposed color, texture, and workmanship.
3. Obtain acceptance of completed panel from Construction Manager before beginning work.
4. Retain accepted panel during construction as a standard for judging completed work. Do not
after, move, or destroy panel until work is completed.
C. Pre - installation Conference:
1. General Contractor shall arrange meeting no less than seven days prior to starting work.
2. Attendance:
a General Contractor.
b. Coating subcontractor.
a Architect/Owners Representative.
d. Coating manufacture representative /distributor.
3. Agenda:
a Substrate condition.
b. Sequence and method of application of coating system.
1.05 PROJECT CONDITIONS
A. Environmental Requirements:
1. Do not apply on frozen or frost - filled surfaces.
2. Do not apply if temperature is below 40 1F or expected to fa;! below 40 °F within 24 hours.
3. Product material from freezing.
3800 -1
WM - Lake Elsinore, CA
two Film, W,
WS BUT A2@99930WOMKOWKS"B"'
WI11 S AVAILAUS AT 'iMM
T OA F
Fr
July 16, 1993
PART 3 EXECUTION
3.01 EXAMINATION AND PREPARATION
A. Allow 28 -30 days for curing of concrete /mortar.
B. Examination:
1. I xamAe substrate to which finely textured coating is to be applied. Do not proceed ft
unsatisfactory conditions exist which hamper proper application.
2. Beginning of application means acceptance of substrate condition.
C. Preparation:
1. Surfaces to receive system shall be free of defects such as honeycombs, form marks, tie holes,
concrete droppings, laitance, dirt, dust, grease, form release treatments, efflorescence, curing
compounds, paint and any other foreign material.
2. Fill holes in excess of 3/8 inch.
D. Beginning of application means acceptance of substrate.
3.02 APPLICATION
A. General:
1. Begin system application at rear of building and work toward front. Begin application of system
in the preseese of manufacturers Technical Representative.
2. Sealer or filler: Apply in accordance with manufacturers recommendations.
3. Decorative Acrylic Coating:
a. Apply material at a rate recommended by manufacturer.
b. Apply material by brush, roller, plaster type sprayer, or low pressure sprayer.
a Back roll brushed or sprayed material; cross roll roller - applied material.
d. Finish material so that brush and roller strokes are in one direction.
B. Application (Thorn System Products) Cementitious Block filler:
1. Dampen wall prior to and during application. Change of color of masonry unit should be noted.
Do not soak wall excessively or allow water to accumulate on the surface.
2. Apply brush, plaster type or airless sprayer coat of Cementitious Block Filler to the surface of
flat, split- faced, rock -faced or fluted masonry units. One unit of cementitiou;; block filler (5 -6 gals)
will cover 600 -750 sq If of flat faced CIV; 350 -500 sq It of split- faced, rock faced and fluted
CMU. Using plaster type sprayer, spray -apply at 35 -40 PSI air pressure at spray nozzle, using
a 3116" or 1/4" spray orifice.
3. Using a wet clean soft nylon bristled brush or broom, work the fill coat in a horizontal direction to
fill pores. Lay oft fill coat in a vertical direction. Do not allow brush or broom to become loaded
with material. Backroll surf..ce with 3/4" nap roller using downward finish strokes to remove any
brush strokes. Do not let material sot or harden before backroliing.
4. Finish from breakpoint to breakpoint. Do rat stop in middle of wall.
5. If hot, dry and windy conditions exist, let fill coat set for 24 hours, cure by fog spraying on
second day if conditions are hot dry or windy.
6. Decorative Acrylic Coating:
a. Stir Thorocoat thoroughly with mechanical mixer to assure complete, uniform dispersion
throughout.
b. in extremely hot, dry weather, slight damping of the surface with clean, potable water is
acceptable prior to applyying Thorocoat- Smooth.
a Apply 7horoccat- Smoofh by ro!!er, plaster or low pressure sprayer at a rate not to exceed
80 square feet per gallon.
d. Finish material so that roller strokes are in one direction.
C. Tolerances: Finish coat must be pinhole free.
3.03 FIELD QUALITY CONTROL
A. All exterior masonry surfaces shall receive complete and thorough coverage or specified masonry
weatherproofing system in colors as scheduled on Drawings.
B. Maintain schedule of application of system in field office for Owners review.
NM - Lake Elsinore, CA
s
B. Galvanized Metal (includes garden center canopy): Solvent Base, Gloss, Alkyd -Resin Enamel.
1st Coat: PPG Speedhide Galvanized Steel Primer Interior /Exterior, 6 -209 series.
2nd Coat: PPG Speedhide Gloss -Oil Interior /Exterior- Interior Enamel, 6 -252 series.
Paint inside surfaces of guttering.
C. Exterior Insulatior and Finish System: Water Base, Flat, Vinyl Acrylic.
1 st Coat: PPG Speedhide Acrylic Latex House Paint, 6 -650 series.
2nd Coat: PPG Speedhide Acrylic Latex House Paint, 6 -650 series.
D. Concrete Unit Masonry (Accent Stripes): Water Base, Semi - Gloss, Vinyl Acrylic Latex.
1 st Coat: Special Coating per Section 09800.
2nd & 3rd Coat: PPG Interior /Exterior Water Semi -Gloss Enamel, 53 -610 series.
Back roll both paint coats as required to ensure good coverage.
3.08 PAINTING AND FINISHING SCHEDULE (INTERIOR)
A. Ferrous Metals: Solvent Base, Lo- Lustre, Alkyd Resin. (Hollow Metal Doors and Frames, Pipe --
Bollards, Stair Stringers, and Handrails.)
1 st Coat: PPC Speedhide Quick -Drying Machinery and Equipment Primer, 6 -205.
2nd Coat: PPG Speedhide Low Odor Interior Enamel Wall and Trim Lo- Sheen -Oil, 6 -90 series.
B. Gypsum Board: Water Base, Eggshell, Latex Enamel.
1 st Coat: PPG Speedhide Quick-Drying Interior Latex Primer - Sealer, 6 -2 series.
2nd Coat: PPG Speedhide Latex Eggshell Enamel, 6 -411 series.
C. Wood (Stained): Clear Varnish over Oil Stain. i
1 st Coat: "Cape Cod Grey" stain, to match wall paneling, by Olympic Stain. Fill wood with natural
ppastewood filler tinted with oil stain before final finish,
2nd Cope: Rez Varnish, Alkyd Gloss Interior Clear, 77 -4 series.
3rd Coat: Rez Varnish, Interior Satin Oil Clear, 77' series.
D. Wood (Stockroom Shelving): Clear sealer only.
1 st Coat: PPG Speedhide Ouick -Drying Interior .'anding Wood Sealer and Finish (clear), 6 -10 series.
E. Concrete Unit Masonry (Sales Areas): Water Base, Eggshell, Vinyl Acrylic Latex.
1st Coat: PPG Speedhide Masonry Block Filler, 6 -7 series.
2nd & 3rd Cc at: PPG Speedhide Eggshell Latex Enamel. 6 -411 series.
Back roll both filler and paint coats to ensure good coverage. i
F. Concrete Unit Masonry (Stockroom area): Water Base, Eggshell, Vinyl Acrylic Latex.
i
1st Coat: PPG Speedhide Masonry Block Filler, 6-7 series.
2nd & 3rd Coat: PPG Speedhide Semi -Gloss Latex Enamel, 6 -510 series.
Back roll both filler and paint coats to ensure good coverage.
G. Concrete Unit Masonry (Automotive Areas)* Water Base, Gloss, Vinyl Acrylic Latex.
1st Coat: PPG Speedhide Masonry Block Filler, 6 -7 series. t
2nd & 3rd Coat: PPG Interior /Exterior Water Base Gloss Enamel, 53.610 series.
Back roll both filler and paint coats to ensure good coverage.
H. Concrete Floors: Alkyd and Chlorinated Rubber, Flat, OSHA Yellow. '
Primer: None
Finish: 2 coats, MWF 5.0 mils. Pittsburgh Traffic and Zone Marking Paint 11 line.
END OF SECTION
WM - Lake Elsinore. CA
a-
09900.4 '
July 16,1993
1
B
r
The
E. Hang smooth, non - matching patterns by pasting strips on the wall, overlapping the edges, and
double- through both thicknesses. contractor shall provide all wall primer, sealer and adhesive as recommended by the wallcovering cutting"
manufacturer. 1. Use a 0.04" or 0.06" zinc or aluminum strip between well and material when cutting, to avoid
gouging the wall.
2.0 ?- ADHESIVES
F. Use a stiff - bristled brush or flexible broad knife to eliminate air pockets and to secure the
A. Manufactured products recommended by wallcovering manufacturer for used in applying their specific wallcovering to the wall surface.
product. i
G. Fill spaces above and below doors and similar areas in sequence from the roll, not later when all full -
B . Do not use wheat paste or cellulose paste with vinyl wallcoverings. 4 length pieces have been installed.
C. Do not thin adhesives. I H. Remove excess paste from each seam as it is made and before proceeding to next seam. Use
sponge dampened with plain warm water, but not wringing wet. Wipe seam clean with dry cloth
towel.
PART 3 EXECUTION !
I. Examine each seam carefully when completed. Trim additional selvage where required to achieve a
3.01 EXAMINATION color and pattern match at seams.
A.
jI
Examine area in which work Is to be performed. Report in writing to the architect all prevailing h J. Wrap wallcovering 6" beyond outside comers and 3" at Inside corners.
conditions that may ad%ersely affect satisfactory execution of this Work. Do not proceed with work ( 1. Cutting at corners will not be accepted.
until unsatisfactory conditions have been corrected. ! 2. Horizontal seams will not be accepted other than as indicated or required for pattern change.
1. Make sure surfaces to receive wallcovering are clean, true, and free of irregularities.
K. Install wallcovering to extend from 2" above finish floor to ceiling line or above. Wallcovering shall be
B .
I
Schedule installation of wallcovering as late as possible to prevent damage during construction and secure, smooth, clean, without wrinkles, gap,:,-and overlaps at completions of work.
movement of materials.
3.04 CLEANING
C. Starting work constitutes acceptance of the existing conditions and responsibility for correcting all
unsatisfactory and defective work encountered. C A. Clean wallcoverings of all adhesives, dust, dirt, and other contaminants.
3.02 PREPARt.TION B. Remove debris and leave area in neat and clean condition.
A. Surface to receive wallcovering shall meet the minimum requirements established by the wallcovering I 3.05 PROTECTION
manufacturer. k
A. Protect finished work installed by other trades prior to work under the Section. Replace all work
B. Gypsum wallboard substrate shall have all fasteners recessed, with all joints and fastener i damaged by workmen of this trade without additional cost to Wal -Mart.
depressions taped, speckled and sanded. The surface to receive wallcovering shall be uniformly
level and smooth. END OF SECTION
1. Fill nicks, gouges, and other minor imperfections of substrate surfaces with latex filler. Sand
smooth flush with surface.
2. Follow with prime coat of sealer recommended by wallcovering manufacturer.
C. Painted Surfaces: Wash down painted surfaces with trisodium phosphate, rinse with clear water. i
Open up surfaces with rough sandpaper for bond, then sealglossy `
1. Remove bleeding paint, flaky paint, and wood stain. I
D. Metal Surfaces: Remove rust, dirt, and grease. Prime with recommended metal primer. j
E. Sizing: Size all walls prior to installation in strict accordance with manufacturer's printed instructions. C
i
F. The contractor shall be responsible for all defects in the substrate which appear in the finish surface
after completion.
3.03 INSTALLATION
A. Remove hardware, accessories, plates and similar items to allow fabric to be installed. Upon
completion of each space, reinstall all items removed.
13.
I
Prime and seal substrates per wallcovering man0acturers recommendations for the type of substrate
being covered. c
C. Follow the adhesive manufacturer's directions for mixing and applying adhesive.
D. Use wallcovering panels in the exact order as they are cut from rolls; use rolls in consecutive order. i
Apply paste to the back using a roller or paste brush. ;-
i
f
f
09950.2 099503
WM - Lake Elsinore, CA July 16, 1993 ', WM - Lake Elsinore, CA July 16, 1993
4
x ..;•1LAI,..12.f.5R.LN{Y.,iNlo9n yrla iYL.Y:3.rr:+LL4k4'JY w,teiW4 "ii,. w , n.. ..nev.tis..w...,w„AUa.,.rr,.w.' .d:::`s
w,.,.+.i :•..dam%:.. ..... J_.. . .,.,.:.. ' .. .. . :...:. ..... ... ...:.e,.' ,..,.. I, -, ,. ,. ,, :. ,., ..,... ,
THIS FILM WAS PRODUCED 'FROM
THE BEST AND MOST COMPLETE
DRAWINGS AVAILABLE AT THE
TI0 OF FILM110.
1,
e ...
W
4, Protect surfaces from rapid drying where windy, hot, and dry conditions exist.
S. Protect from precipitation for 24 hours after application.
6. Avoid applying material during rapid and extreme changes in temperature to prevent thermal
shock cracks Boringg the curing process.
7. The following conditions may require damping the surface prior to and during application:
a. Wind- caused rapid drying of surface.
b. Excessive surface temperature.
a Excessive air temperature.
d. Direct sun.
e. Low humidity.
1.06 WARRANTY
A. Provide five year material and labor warranty to cover:
1. Waterproofing above grade.
2. Br ndng.
3. Weathering.
B. Manufacturers "Intent to Warrant" must be issued to the General Contractor and Wal -Mart before
app?-lion commences.
PART PRODUCTS
2.01 MANUFACTURERS
A. Subject to compliance with requirements, provide coatings of one of the following manufacturers:
1. Thom System Products.
2. Sonnebom Building Products.
B. Substitutions: None accepted.
2.02 COATINGS
A. Cementftious Coatings, by Thoro System Products:
1. CementRlous Block Filler: Cement@lous, acrylic - modified waterproofing block filler, made from
the following components.
a. Super Quickseal - White.
b. Thorosheen.
a Water.
2. Decorative Acrylic Coating: Thorocoat- Smooth, by Thom Svstem Products.
3. Colors: As Indicated on drawings.
B. Acrylic Coatings, by Sonnebom: Hydrocide Colorflex by Sonnebom Building Products.
1. Block Filler: Colortiex Block Filler #749 for system, by Sonnebom Building Products, as
required by system manufacturer for warranty.
2. Colors: As Indicated on drawings.
2.03 MIXES
A. Mix In strict accordance with printed instructions of manufacturer. Use approved mechanical mixer.
Do not use frozen, caked, or lumped materials. Clean mechanical mixers and containers after each
mixing; keep batdi free of material and sealers from previous mixes.
B. Mixing (Thom System Products): "One unit" of cementitious block filler shall be mixed as follows.
1. Mix one 50 lb. bag of Super Quickseal together with 12 to 16 quarts of clean, potable water
until a creamy batter consistency is achieved, with uniform color. Hot temperatures and low
humidity will require maximum amount of water to achieve the creamy consisten .y.
2. Let material set for five to fifteen minutes to soak, then temper back by adding one (1) gallon of
Thorosheen -Tint Base.
C. Mixing (Sonnebom Building Products): Mix in strict accordance with manufacturers published
instructions.
09600.2
WM - Lake Elsinore, CA July 16,1993
i
i
i
i
f
i
I
I
3.04 COLOR SCHEDULE
A. Lt. Grey:
1. "Early Dawn" (NAM -034), by Thom System Products.
2. "Dover Grey" (014 -56P), by Sonnebom Building Products.
B. Dk. Grey:
1. "Bagdad Grey" (NAM -308 by Thom System Products.
2. "Drum Hill Grey" (015 19'k by Sonnebom Building Products.
END OF SECTION
WM - Lake Elsinore, CA
COMM
SINN AVAxLA» AT 'tMt
I OF if I
i
i
l
4
July 16,1993
SECTION 09900
WM: 061893
PAINTING
PART GENERAL
1.01 SUMMARY
A. Section Includes:
1. Paint and finish interior and exterior exposed surfaces.
2. Include field painting of exposed pipes and ducts, hangers, exposed steel and Iron work, and
primed metal surfaces of equipment installed under Mechanical and Electrical Sections.
3. Above roof Items including, but not limited to satellite support steel, roof hatch, inside surfaces
of gutters, sheet metal counterflashing and top surfaces of front and Garden Center canopy
supporting steel.
B, Items Not Painted:
1. Aluminum, brass, bronze, stainless steel, and chrome plated steel.
2. Pre- finished;tems, such as toilet compartments and acoustical ceiling materials.
3. UL, FM and other code- required labels.
4. Equipment Identification, performance rating, or name plates.
1.02 SUBMITTALS
A. Submit the following under provisions of Section 01300.
B. Product Data: Submit on Product Compliance Letter, the manufacturers, paint color names and
numbers selected.
C. Samples: Exterior only; color and manufacturer.
1. Submit two 12x1 Inch hardboard samples of each color and texture. Resubmit until color,
texture, and sheen are accepted.
2. For masonry, provide two 4 inch squares of masonry for each type of finish and color. Indicate
filler, primer, and finish coats.
3. If directed by Wal -Mart Construction Manager, duplicate painted finishes of acceptable samples
on actual wall surfaces for further acceptance.
1.03 DELIVERY, STORAGE, AND HANDLING
A. Deliver paint materials in sealed original labelled containers, bearing manufacturers name, type of
paint, brand name, color designation, and instructions for mixing and/or reducing.
B. Provide adequate storage facilities. Store paint materials at minimum ambient temperature of 45 "F in
well ventilated area.
C. Take precautionary measures to prevent fire hazards and spontaneous combustions.
1.04 ENVIRONMENTAL REQUIREMENTS
A. Apply paint finishes only when moisture content of surfaces is within acceptable ranges for type of
finish being applied.
B. Ensure surface temperatures or surrounding air temperature is above 40 °F before applying alkyd
finishes; above 45 °F for interior latex, and 50 °F for exterior latex work. Minimum for varnish and
transparent finishes Is 65 "F.
C. Provide adequate wmiri-ious ventilation and sufficient heating facilities to maintain temperatures
above 45 °F for 24 hours before, during and 48 hours after application of finishes.
1.05 EXTRA MATERIALS
A. Furnish the following, to Wal -Mart, under provisions of Section 01700.
1. Provide 2 gallons of each color for the Pharmacy area.
2. Provide c gallons of each color, type and surfacte texture for general sales area.
WM - Lake Elsinore, CA
a•
y.
A
F. Soap Dispensers: Wall mounted globe type for liquid soap; one per each lavaiory. Mount at side
of faucet over lavatory.
1. Model No. 659, by Bradley.
2. Model No. 0350, by American Specialties.
3. N;odel No. B44, by Bobrick.
4. Model No. U118A, by A.J. Washroom.
5. Model No. 307.6, by McKinney /Parker.
6. Model No. SD -3A, by Tubular Specialties.
G. Electric Hand Dryers: Model No. Al by World Dryer Corporation.
1. Color: Snow White PWHC.
2, Substitutions: None accepted.
END OF SECTION
108003
IE
I
WM - Lake Elsinore, CA July 16, 1993 t WM - Lake Elsinore, CA July 16, 1993 i WM - Lake Elsinore, C 4 July 16, 1993
I i
t
j
f
Y
w , . ........ e. .• .,n .i ; r, ..• ..: ;n.. .:. :.. ...: i,. •rt1 .., .v t cei. \.rL s •A.it• fb4++^n ,. 1 1'{ .Y , , • • s ,.. .. ,.... .. ., 1.,. . 4.:1 J.,nh. . Wl1- l,A Lr,.tl +4,i.,rew.4.w. Hl .4. 1 s .
i,,., ..,
MINi..r av ' sr •.. 1 Y,W . ..M ..•••••-
T
THIS FILM WAS PRODUCED FR17M'
THE 13 ST AND MOST COMPLETE
DRAWINGS AVAILABLE AT THE
Tip OF FIIJIIXGo__,.
i
f,
SECTION 10165 SECTION 10800
WM: 09242
PLASTIC LAMINATE TOILET COMPARTMENTS
WM: 05202
TOILET AND BATH ACCESSORIES
PART GENERAL PART1 GENERAL
1.01 SUMMARY 1.01 SUMMARY
A. Work Includes: A. Section Includes:
1. Plastic laminate toilet compartments, floor mounted, head rail braced. 1. Toilet accessories and attachment hardware.
2. Urinal screens, wall mounted.
3. Attachment hardware. 1.02 REFERENCES
I. B. Related Sections: A. American National Standards Institute (ANSI):
1. Section 062f0 - Finish Carpentry: Framing and plates within walls. Coordinate plastic laminate 1. ANSI Al 17.1 - Specifications for Making Buildings and Facilities Accessible To and Usable by
selection. Physically Handicapped People. j 2. Section IVd00 - Toilet and Bath Accessories: Coordinate compartment installation with
I subsequent accessory Installation. 1.03 SUBMITTALS
1.02 REFERENCES A. Submit the following under provisions of Section 01300.
A. ANSI At 17.1 - Safety Standards for the Handicapped. B. Product Data: Submit in letter form through General Contractor to Wal -Mart Construction Department
the manufacturer and model selected.
1.03 SUBMITTALS
i
t A. Submit the following under provisions of Section 01300. PART 2 PRODUCTS
B. Product Data. Submit on Product Compliance Letter the manufacturer and model selected. 2.01 MANUFACTURERS
A. Subject to compliance with requirements, provide toilet accessories of one of the following:
PART 2 PRODUCTS 1. Bradley Corporation, Washroom Accessories Division, Laurel, NJ, (609)235 -7420.
2. American Specialties, Inc., Yonkers, NY, (914)4,'6 -9000.
2.01 TOILET COMPARTMENTS 3. Bobrick Washroom Equipment, Inc., North Hol'ywood, CA, (6;8)764 -1000.
A. Subject to compliance with requirements, provide toilet compartments of one of the followingIPqP9
4. A. & J. Washroom Accessories, Windsor, NY, (914)565 -3050.
5. McKinney /Parker, Scranton, PA, (717)346 -7551.
manufacturers: 6. Tubular Specialties Mfg., Inc., Los Angeles, CA, (213)515.4801.
1. Concord, b; Accurate Partitions Corp.
2. Type HB, by All American Metal Corp: ( AAMCO) B. Substitutions: None accepted.
3. Type PL -FF, by American Sanitary Partition Corp.
4. Overhead braced, by AMPCO Products, Inc. 2.02 MATERIALS
5. Series 40, by General Partitions Mfg. Corp.
6. Embassy, by Global Steel Products Corp.
7. Metropolitan, by Knickerbocker Partitions Corp.
A. Stainless Steel: AISI Type 302/304.
8. Corinthian Type RX500, by Metpar Steel Products Corp. B. Mounting Devices: Hot-di p galvanized after fabrication or of same material as accessory unit.
i
9. Overhead Braced, by Weis /Robart Partitions Inc.
1
B. Urinal Screens: Wall hung type, 24" x 42" to match toilet compartments.
C. Adhesive: Epoxy type contact cement.
C. Substitutions: None acce ted. P
D.
i
Finishes:
1. Chrome /Nickel Plating: Polished finish.
t 2. Stainless Steel: No. 4 luster finish, unless specified olharwise.
2.02 MATERIALS 3. Shop Primed Ferrous Metals: Pretreat and clean, spray apply one coat primer and bake.
A. 1/16 inch plastic laminate high pressure laminated to solid 45 lb density core. j 2.03 FABRICATION
1. Panels: 3/4 inch thickness.
2. Doors: 1 inch thickness. A. Weld and grind smooth joints of fabricated components.
3. Pilasters: 1 -114 inch thickness.
4. Reinforcement for Anchorages: 12 gage. B. Form exposed surfaces from one sheet of stock, free of joints. Form suit ^ces flat without distortion.
B. Pilaster Shoes: 3 inches high; Type 302/304, No. 4 stainless steel finish.
Maintain flat surfaces without scratches or dents.
C. Provide steel anchor plates and anchor components for installation on building finishes. Hot -dip
C. Attachments, Screws, and Bolts: Stainless steel; tamper root type; heavy cut extruded aluminumPPyPvYY galvanize ferrous metal anchors and fastening devices. 1 brackets.
D. Back paint components where contact is made with owlling finishes to prevent electrolysis.
E. Shop asserble components and package complete with anchors and fittings.
10165 -1 10800 -1
F. Soap Dispensers: Wall mounted globe type for liquid soap; one per each lavaiory. Mount at side
of faucet over lavatory.
1. Model No. 659, by Bradley.
2. Model No. 0350, by American Specialties.
3. N;odel No. B44, by Bobrick.
4. Model No. U118A, by A.J. Washroom.
5. Model No. 307.6, by McKinney /Parker.
6. Model No. SD -3A, by Tubular Specialties.
G. Electric Hand Dryers: Model No. Al by World Dryer Corporation.
1. Color: Snow White PWHC.
2, Substitutions: None accepted.
END OF SECTION
108003
IE
I
WM - Lake Elsinore, CA July 16, 1993 t WM - Lake Elsinore, CA July 16, 1993 i WM - Lake Elsinore, C 4 July 16, 1993
I i
t
j
f
Y
w , . ........ e. .• .,n .i ; r, ..• ..: ;n.. .:. :.. ...: i,. •rt1 .., .v t cei. \.rL s •A.it• fb4++^n ,. 1 1'{ .Y , , • • s ,.. .. ,.... .. ., 1.,. . 4.:1 J.,nh. . Wl1- l,A Lr,.tl +4,i.,rew.4.w. Hl .4. 1 s .
i,,., ..,
MINi..r av ' sr •.. 1 Y,W . ..M ..•••••-
T
THIS FILM WAS PRODUCED FR17M'
THE 13 ST AND MOST COMPLETE
DRAWINGS AVAILABLE AT THE
Tip OF FIIJIIXGo__,.
i
f,